Building Facade Coating - Sikagard®-615 DPR

100% Acrylic Coating with Dirt Pickup Resistance (DPR)

Sikagard®-615 DPR is a surface hardening, vapor permeable, tack free, dirt and chemical resistant decorative and protective coating for concrete, masonry, EIFS, and Stucco. Sikagard®-615 DPR is available in light or dark tint bases and can be integrally colored with Colorfast pigments.

• Resistant to dirt pickup and mildew
• Excellent hiding power
• UV Resistant
• High Durability
• Excellent Adhesion
• Can be applied by brush, roller, or spray applications
• Water base VOC compliant
• Vapor permeable
• Does not create a vapor barrier
• Meets SCAQMD Rule 1113 when colored with Colorfast pigments

Usage

Exterior or interior coating for

• Concrete
• Masonry
• EIFS
• Stucco
• Previously applied acrylic-based textured finishes

Advantages

• Resistant to dirt pickup and mildew
• Excellent hiding power
• UV Resistant
• High Durability
• Excellent Adhesion
• Can be applied by brush, roller, or spray applications
• Water base VOC compliant
• Vapor permeable
• Does not create a vapor barrier
• Meets SCAQMD Rule 1113 when colored with Colorfast pigments

Packaging

60 lb (27.7 kg) net weight in plastic pails

Color

Factory tinted to desired color. Flat non-gloss, smooth finish.

Product Details

Product Information

Chemical Base

• Binder base: 100% Acrylic polymer
• Pigment base: Titanium Dioxide
• Water base: VOC compliant

Shelf Life

15 monthsfrom date of manufacture in original, unopened container.

Storage Conditions

Store dry at 45-95 °F (7-35 °C). Condition material to 60-75 °F (15-24 °C) before using. Protect from direct sunlight and freezing at all times. If frozen, discard. Do not stack more than 3 pails high.

Density

12.37 lb/gal at 68°F (20°C)

pH-Value

8.0-10.0

Technical Information

Application

Consumption

Coverage

Theoretical yield per coat: 200 - 240 ft² (18.6 - 22.4 m²)/gal/coat.

Recommended ‘wet’ film thickness: 10 mils (0.25 mm)/coat. Recommended ‘dry’ film thickness: 6 mils (0.15 mm)/coat. Normal coating system is two coats at a total dry film thickness of 12 mils*. Consumption is dependent on porosity of substrate. In addition, allowance must be made for surface profile, unavoidable variation in applied film thickness, loss and waste.

*One coat coverage recommended only for recoating over existing coatings

Application Steps

APPLICATION

Any areas of glass or other surfaces should be masked. Recommended application temperatures (ambient and substrate) 45°-95°F (7°-35°C). Sikagard®-615 DPR can be applied by brush, roller (3/8” Nap Roller recommended), or spray over entire area moving in one direction. Sikagard®-615 DPR Coating exhibits good surface coverage in single application. However, for most uncoated, unprimed surface of concrete, masonry, or drywall, two coats of Sikagard®-615 DPR may be required to obtain adequate hiding of the substrate and best performance. For spray applications, strain the material using a paint strainer. At lower temperatures and high humidity, waiting time to recoat will be prolonged. At higher temperatures, work carefully to maintain a wet edge. As with all coatings, job site mock-ups should always be completed to confirm acceptability of workmanship, material and aesthetics.

NOTE: To achieve a dry film thickness of 12 mils, two coats should be anticipated. For maximum adhesion, (especially on porous substrates) the use of Sikagard® 552W is recommended. Sikagard® 552W primer can be applied by brush or roller. Brushing provides more even and pore free coats and better penetration.

CLEANING OF TOOLS

Water soluble prior to drying. Clean tools and containers with water prior to drying. Cured material can be removed mechanically.

See More

See Less