Sika Corporation -Injection Systems - Sika® Inject-215

DOWNLOADS

Elastic Polyacrylic Injection Resin Used for Permanent Watertight Sealing

Sika® Inject-215 is a low viscosity, elastic polyacrylic injection resin with a fast, adjustable reaction time and high flexibility for the waterproofing of building structures.


Category: below grade waterproofing and dampproofing | damproofing | membrane waterproofing...

MasterFormat: Dampproofing and Waterproofing


Related Products

Overview


Injection Systems - Sika® Inject-215

Elastic Polyacrylic Injection Resin Used for Permanent Watertight Sealing

Sika® Inject-215 is a low viscosity, elastic polyacrylic injection resin with a fast, adjustable reaction time and high flexibility for the waterproofing of building structures.

  • Adjustable pot life between 2 and 15 minutes
  • Hydrophilic chemistry allows cured material to swell upon contact with water, providing additional seal properties.
  • Flexible and solvent free acrylate resin
  • Compatible with water
  • Very good penetration

Usage

  • Sika® Inject-215 is used for the injection of SikaFuko® injection hoses to seal construction joint.
  • Sika® Inject-215 is used to seal water-bearing cracks and voids.
  • Sika® Inject-215 is used for curtain/membrane injections in damp or water saturated ground conditions to waterproof large surface areas.
  • Sika® Inject-215 is used as a post-construction, external injection sealing system for construction, and limited movement expansion or drainage pipe joints, that are, or will be, covered with damp or water saturated soil.

Advantages

  • Adjustable pot life between 2 and 15 minutes
  • Hydrophilic chemistry allows cured material to swell upon contact with water, providing additional seal properties.
  • Flexible and solvent free acrylate resin
  • Compatible with water
  • Very good penetration

Packaging

Approximate yield = 8 US gallons
Resin 2 x 2.0 gallons 30 x 41 lbs = 1.230 lbs
Accelerator 2 x 26 fl. oz.
Hardener-Powder 2 x 14 oz.
Measuring cup 100 ml 1 piece
Mixing Instruction

Color

Yellow

Product Details

Product Information

Shelf Life

12 months

Storage Conditions

Sika® Inject-215 can be stored for up to 12 months in sealed containers and at temperatures between 10 °C and 30 °C.

Density

Approx. 1.08 g/ml (at 68 °F (20 °C))

pH-Value

Approx. 10 (at 68 °F (20 °C))

Total Chloride Ion Content

<0.01%

Viscosity

Approx. 6mPas (at 68°F (20°C), mixture of components)

Technical Information

Swelling

Swelling behavior in demineralized water
Sika® Inject 215 has a medium to high swelling rate and therefore offers additional safety in case of movements/joint movements. The determination of the swelling rate depends of the contact medium, the temperature and reaction time.

Application

Application Information

Mixing Ratio

Example for Mixing:

Ambient Temperature 20oC (68oF)

Required Reaction Time 5 min.

Component A

Accelerator quantity = 4 1/2 fl. oz

Resin = 2 gallons

Component B

Hardener Powder = 1 bag

Water = 2 gallons

Sika® Inject-215 consists of 3 components which can be mixed in dependance of the required reaction times:

  1. 2 gallons of the resin (component A) are activated with 2 fl. oz. to 26 fl. oz of accelerator. The reaction time - see metering chart - is adjusted by the quantity of accelerator used.
  2. The hardener solution (component B) is produced by dissolving 1 bag (14 oz.) of hardened powder in 2 gallons of water.
  3. The pre-mixed components as per point 1 and 2 above are processed with a two component injection pump, having a static mixing unit in a mixing ratio of 1:1.

    Sika® Inject-215 consists of 3 components which can be mixed in dependance of the required reaction times:

  4. 2 gallons of the resin (component A) are activated with 2 fl. oz. to 26 fl. oz of accelerator. The reaction time - see metering chart - is adjusted by the quantity of accelerator used.
  5. The hardener solution (component B) is produced by dissolving 1 bag (14 oz.) of hardened powder in 2 gallons of water.
  6. The pre-mixed components as per point 1 and 2 above are processed with a two component injection pump, having a static mixing unit in a mixing ratio of 1:1.

Application Steps

NOTES ON INSTALLATION

Processing

Injection with two component pump via injection hoses or drill packer

SUBSTRATE PREPARATION

Substrate Temperature 5 °C min. / 40 °C max.

CLEANING OF TOOLS

Sika® Inject-215 is compatible with water, therefore re-injectable injection hoses can be cleaned by vacuum. Tools and injection pumps can be cleaned with water after use. Hardened/cured material can only be removed mechanically.


See More


Specifications

Swelling
Mixing Ratio