Foster™ - Foster® 85-60 QUICK-TAK™ ADHESIVE

DOWNLOADS

FOSTER QUICK- TACKTM ADHESIVE FOSTER QUICK-TACK Adhesive is a high tack, rapid setting water-base adhesive designed for bonding low density (up to 3#/cu. ft.) duct liner, duct wrap and fibrous glass insulations to painted or unpainted steel, galvanized or aluminum surfaces. QUICK-TACK Adhesive is a


Category: HVAC adhesives | adhesives | commercial insulation...

MasterFormat: Adhesives* | Common Work Results for HVAC | HVAC Insulation...


Related Products

Overview


Foster® 85-60 QUICK-TAK™ ADHESIVE



FOSTER QUICK- TACKTM ADHESIVE

FOSTER QUICK-TACK Adhesive is a high tack, rapid setting water-base adhesive designed for bonding low density (up to 3#/cu. ft.) duct liner, duct wrap and fibrous glass insulations to painted or unpainted steel, galvanized or aluminum surfaces.

QUICK-TACK Adhesive is a solvent free, very low VOC synthetic elastomer emulsion. It is non-flammable when wet and fire-resistive when dry. It can be applied to either the metal or the insulation. The dry film stays moisture resistant.

QUICK-TACK Adhesive can also be applied as a contact bond adhesive being applied to both surfaces in areas where water entrapment may be a problem such as polystyrene to metal.

QUICK-TACK Adhesive is ideal for bonding fibrous glass insulation to concrete, block and other masonry surfaces in building construction.

QUICK-TACK Adhesive meets ASTM C916 Type II (ASC-A-7001A, Type II) and NFPA-90A and 90B 25/50 requirements.

QUICK-TACK meets requirements for LEED IEQ 4.1 Low-Emitting Materials, Adhesives and Sealants. Theoretical VOC: 0 g/l with no added VOC components. (<40 g/L, less water and exempt solvent analytically determined by EPA Method 24)

QUICK-TACK Adhesive contains no asbestos, lead or mercury compounds.

LIMITATIONS
Store and apply between 40ºF (4ºC) and 100ºF (38ºC), protect from freezing until dry. Avoid repositioning the insulation after initial placement. Not suggested for use with roll coating machines. Always test plastic foam insulation for warpage when using any water base adhesive. Overhead applications may require mechanical fasteners.


COLOR:
Cream

APPLICATION CONSISTENCY:
Spray, brush or roller

AVERAGE WEIGHT / U.S. GALLON:
10.5 lbs. (1.26 kg/l)

AVERAGE NON-VOLATILE:
54% by volume (64% by weight)

COVERAGE RANGE:
(Subject to type of surface and nature of material to be bonded.)

Spray Application:
300-600 sq. ft. /gal. (7.4 to 14.7 m2 /l) Roller and Brush: 150-600 sq. ft./gal. (3.7-14.7 m2 /l)

BONDING TIME RANGE (FSTM 66):
(Depending upon temperature and humidity) Contact Bond: 15 minutes to 2 hours Single Surface Wet Bond: 0-15 minutes

SERVICE TEMPERATURE LIMITS:
-20ºF to 200ºF (-29ºC to 98ºC)

WET FLAMMABILITY (ASTM D 3278):
No flash to boiling 212ºF (100ºC)

SURFACE BURNING CHARACTERISTICS (ASTM E 84):
Flame Spread: 0
Smoke Developed: 0
Tested at coverage rate of 200 sq. ft./gal. (4.9 m2 /l).
Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board. The flame spread may vary at different product thicknesses and/or when applied over other surfaces.

QUICK-TACK ADHESIVE
is produced under the classification and follow- up service of Underwriter's Laboratories, Inc.

TM TradeMark of

H.B. Fuller Construction Products Inc.


Visit us on the web at www.fosterproducts.com


See More


Sweets app for Revit – Learn More