TUFFLEX Polymers - UREA-TUFF 6500-VT - Base Coat

DOWNLOADS
Product Description UREA-TUFF 6500-VT is a two component, fast setting, rapid curing and solvent free Aliphatic Polyurea Elastomeric Coating. It is designed for vehicular decks as well as heavy duty pedestrian decks and roof decks.

Category: elastomeric coatings | roof coatings | waterproofing...

MasterFormat: Pedestrian Traffic Coatings | Membrane Roofing | Elastomeric Coatings...



TUFFLEX Polymers
10880 Poplar Avenue
Fontana, CA 92337
Tel: (888) 883-3539

awren@tufflexpolymers.com

http://www.tufflexpolymers.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


UREA-TUFF 6500-VT - Base Coat


Product Description

UREA-TUFF 6500-VT is a two component, fast setting, rapid curing and solvent free Aliphatic Polyurea Elastomeric Coating. It is designed for vehicular decks as well as heavy duty pedestrian decks and roof decks. UREA-TUFF 6500-VT can be applied to properly prepared interior or exterior concrete, plywood and metal surfaces. It is suitable for application in temperatures as low as 32°F and is rather insensitive to moisture.


General Information

Composition: Liquid applied, two-component, flexible, extremely low odor, hybrid polyurea elastomeric coating.

Basic Uses: For waterproofing parking decks, walking decks, roof decks, mechanical room floors, etc. Designed for vehicular and heavy duty pedestrian traffic.

Limitations: All surfaces must be completely free of foreign matter and primed with TUFF-POXY PRIMER #3. UREA-TUFF 6500-VT has a relatively short work life, so once it is mixed, the coating must be poured onto the surface and applied immediately.

Colors: Sidewalk Grey and Monterey Sand. Custom matched colors are available with minimum required quantities.

Sizes: Available in 4.5 gallon kits and 1.5 gallon units.


Product Installation

Surface Preparation:All surfaces which are to receive UREA-TUFF 6500-VT shall be free of contamination such as water, curing compounds, hardeners, bond breakers, paint, etc. Power trowel followed by a light broom finish is recommended for concrete surfaces. It is desirable to watercure concrete in lieu of using curing compounds. The concrete surface must be thoroughly cleaned by shot-blasting, sand blasting or mechanical grinding followed by the thorough removal of any resulting residue.

Except for non-moving shrinkage cracks, all other cracks must be sealed with UREA-TUFF 6500-VT and taped with 4” TUFF-TAPE “PW” Polyester Reinforcing Fabric. All surfaces must be primed with TUFF-POXY PRIMER #3 prior to application of the coating system. Prime at a rate of 250-300 square feet per gallon.

Application: Lightly stir the A-Component (pigmented side) for 2-3 minutes using a Jiffy mixing blade to evenly distribute the pigments that may have settled to the bottom of the container. Then pour the “B” Component (clear side) into the “A” Component. Scrape the container to drain all the “B” Component into the “A” Component. Mix thoroughly using a Jiffy mixing blade attached to a low speed drill to a uniform color without any streaks. Mix for 2-3 minutes. Once mixed, immediately pour UREA-TUFF 6500-VT onto the surface of the substrate.

Use a notched squeegee to evenly apply the material, then backroll using a short nap roller to break air bubbles. NOTE: Higher temperatures will reduce the work life. UREA-TUFF 6500-VT shall be applied to the primed concrete at a rate of 67 square feet per gallon. Following a 4-8 hour cure time of the first coat, apply a second coat of the UREA-TUFF 6500-VT at the rate of 80 square feet per gallon and while coating is in a fluid condition, broadcast desired quantity of 16 mesh aggregate and backroll.

After a 4-8 hour cure, clean off any loose aggregate and apply a third coat of UREA-TUFF 6500-VT at a rate of 100 square feet per gallon. Broadcast 16 mesh aggregate and backroll. Allow 24 hours cure time (depending on ambient and substrate temperature) before allowing moderate traffic on the finished system.


Maintenance

Since, as with all deck coatings, the topcoat is subject to staining by such foreign matter as nitrates, fertilizers, hard water, and other substances, it must be maintained. Please refer to the Maintenance Manual for proper maintenance procedures. The manufacturer is not liable for staining caused by hard water deposits, nitrates, fertilizers and other foreign matter.

If UREA-TUFF 6500-VT is damaged, it can be repaired by abrading the surface, cleaning the surface with acetone or xylene and recoating it with the UREA-TUFF 6500-VT coating.


Warnings & Hazards

Before using the products, always refer to MSDS for important warnings and safety information. Use only in areas with adequate ventilation. Avoid breathing vapors. Keep primers away from heat and flame. Avoid contact with eyes and skin. In the event of skin contact, remove immediately and wash with warm, soapy water. Wear suitable eye protection. Always wash hands before eating. This material is for professional use only.


Limited Warranty

TUFFLEX POLYMERS (TUFFLEX) warrants this product to be free of defects in workmanship and materials only at the time of shipment from our factory. If any TUFFLEX materials prove to contain manufacturing defects that substantially affect their performance, TUFFLEX will, at its option, replace the materials or refund its purchase price.

This limited warranty is the only warranty extended by TUFFLEX with respect to its materials. There are no other warranties, including the implied warranties of merchantability and fitness for a particular purpose. TUFFLEX specifically disclaims liability for any incidental, consequential, or other damages, including but not limited to, loss of profits or damages to a structure or its contents, arising under any theory of law whatsoever.

The dollar value of TUFFLEX’s liability and buyer’s remedy under this limited warranty shall not exceed the purchase price of the TUFFLEX material in question.


See More


Specifications

Technical Data
PROPERTY TYPICAL VALUE TEST METHOD
Work Life 15-25 minutes @77°F, 50% R.H.
Cure Time (Initial) 2-4 hours @77°F, 50% R.H.
Viscosity at 77°F 33±5 poise Brookfield
Weight per gallon
A-Component
B-Component
9.3 pounds
8.3 pounds
-----
Percent Solids Content 100% (weight)
100% (volume)
ASTM D-2369
Hardness 80 Shore A ± 3 ASTM D-2240
Tensile Strength 3200 psi ± 300 ASTM D-412
Percent Elongation 450% ± 50 ASTM D-412
Adhesive Peel Strength on Primed Concrete 35 pli ASTM D-903
Water Absorption 1.2% by weight ASTM D-471
Moisture Vapor Transmission 3.9 perms ASTM E-96
Chemical Resistance (Commonly encountered acids, salts, and oils) Superior Resistance D-3476
Abrasion Resistance 2 mg. wt. loss ASTM D-4060
30 dry mil film on 4”x4” metal
C-17 wheel, 1000 rev., 1000 gr. weight
Tear Resistance 280 pli ± 30 ASTM D-624
V.O.C Content 0 grams/liter Calculated
U.V. Stability (2000 Hours) No cracking or crazing Q Panel Weather-O-Meter
Sweets app for Revit – Learn More