Flooring Primers & Moisture Barriers - Sika® MB Redline

Solvent Free, Fast Epoxy Moisture Barrier

Sika® MB Redline is a 2-component, rapid curing, solvent free, low viscosity, epoxy moisture control system for use with all flooring systems that require protection from subfloor moisture.

• Cures in 3 hours for fast turnaround jobs
• Can be used with carpet, resilient flooring, wood flooring, floating floors and all types of floor that require subfloor moisture protection
• Solvent-free (100% solids)
• Easy roller applied application, low viscosity
• Convenient, easy to mix packaging
• Shorter construction periods
• Excellent penetration and stabilization of the substrate
• Reduction of adhesive consumption
• Suitable for use on floors with radiant heating
• Compatible with SikaBond® wood flooring adhesives and Sika® Levels.

Usage

• Moisture barrier to help control moisture propagation in cementitious substrates with a moisture content not exceeding 6 % by Tramex Method, residual moisture up to 100 % R.H. or 25 lb/1000 ft²/24 h (11.4 kg/92.9 m²/24 h)
• For substrate consolidation on concrete, cement and gypsum screeds
• Adhesion promoter for old and new adhesive residues in conjunction with other Sika® products

Advantages

• Cures in 3 hours for fast turnaround jobs
• Can be used with carpet, resilient flooring, wood flooring, floating floors and all types of floor that require subfloor moisture protection
• Solvent-free (100% solids)
• Easy roller applied application, low viscosity
• Convenient, easy to mix packaging
• Shorter construction periods
• Excellent penetration and stabilization of the substrate
• Reduction of adhesive consumption
• Suitable for use on floors with radiant heating
• Compatible with SikaBond® wood flooring adhesives and Sika® Levels.

Packaging

2 gal (7.6 L) pail

Color

Red tint

Product Details

Sustainability / Certifications / Approvals

• Meets ASTM F 3010

Product Information

Two component epoxy

24 months from date of production if stored properly in undamaged sealed containers

Store dry at 50-77 °F (10-25 °C). Protect from moisture.

66 lb/ft³ (1.05 kg/l)

Application

Application Information

50°-86 °F (10°-30 °C)

50°-86 °F (10°-30 °C)

Must be minimum 5 °F (3 °C) above the measured dew point temperature.

Application Steps

• Substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust, and loose or friable particles. Paint, laitance, and other poorly adhering contents must be mechanically removed.
• Substrate must have an open textured surface to allow Sika® MB Redline to penetrate. (i.e. Blast cleaning, grinding are considered acceptable means to achevie the desired surface profile. Acid and chemical etching are not acceptable).
• At least 50 % of the surface area must be cleared of residual adhesive and cutbacks. (i.e. by grinding or mechanical substrate preparation)
• Old cutback can contain asbestos which is dangerous for the health so do not grind, sand or blast. Refer to the Resilient Floor Covering Institute’s publication “recommended work practice for removal of resilient floor coverings” for instruction.
• Minimum substrate compressive strength > 1,160 psi. Tensile Bond strength > 116 psi at the time Sika® MB Redline is applied.
• Repair with Sika^® Level SkimCoat or SikaQuick^® mortar before priming.
• The floor must be cleaned with an industrial vacuum prior to installation of the Sika® MB Redline.
• On fiber reinforced concrete, fibers should be flamed off the surface prior to application of Sika® MB Redline as a moisture barrier.
• Before overall installation begins, Sika^® recommends the application of several small test patches to determine primer application requirements and acceptability of final product performance.

• Add one full can of Component A to one full can of Component B then mix with an electric drill and mixing (Jiffy Mixer type) paddle at a low speed to reduce air entrainment (300-400 rpm).
• Using a paint stick or similar is not sufficient to mix the product.
• A minimum mixing time of 3 minutes shall be observed; mixing shall continue until a homogeneous mix has been achieved.
• Scrape sides of pail with paint stick or paddle to ensure all contents are thoroughly mixed together.
• Unmixed material applied to the floor will not cure properly.

• Clean all tools and application equipment with cleaning solvent (Xylene, MEK are effective).
• Hardened/cured material can only be removed mechanically.

See More

See Less