Infrared Dynamics -Sunpak Heaters

DOWNLOADS

These heater have been transforming chilly patio into comfortable outdoor spaces for decades.

The Sunpak® Models S25 & S34 are outdoor rated heaters available for use with natural or propane gas. These heaters can be either wall or ceiling mounted.


Category: CSA design certified heaters | fuel fired heaters | gas fired unit heaters...

MasterFormat: Residential Equipment | Gas-Fired Radiant Heaters | Fuel-Fired Unit Heaters...



Infrared Dynamics
3830 Prospect Ave
Yorba Linda, CA 92886
Tel: (888) 317-5255
Fax: (714) 572-6093

rcowan@infradyne.com

https://infradyne.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


Sunpak Heaters

These heater have been transforming chilly patio into comfortable outdoor spaces for decades.

The Sunpak® Models S25 & S34 are outdoor rated heaters available for use with natural or propane gas. These heaters can be either wall or ceiling mounted. The optional mounting kit allows this heater to be mounted from above keeping the patio deck free and clear. Heat coverage varies depending on the wind exposure on patio. The average spacing between the heaters is 10 feet apart.

Sunpak® comes with a 24 VAC spark ignition system which includes flame monitoring through flame rectification. All Sunpak Heaters require an external 24 VAC source.

As an unvented gas heater, Sunpak® heaters need a continuous supply of fresh air and proper ventilation of combustion gases to operate safely. This heater is not suitable for inside residences and other confined areas where the operational and safety requirements of this heater cannot be met. Refer to heater instructions, available online or from manufacturer for complete information.

The Sunpak® heater design offers a slim profile which works well in a wide variety of patio settings. Sunpak® heaters are available in either black powder coat or a 304 stainless steel finish.

Sunpak Heaters Features:
  • Dimensions: 8 x 8 48 inches
  • Input Rating:
    S25: 25,000 BTU/HR
    S34: 34,000 BTU/HR
  • Fuel Type: Natural or Propane Gas
  • Ignition: Electronic
  • 24 VAC Transformer: Not Included
  • Mounting Kit: Optional
  • Wind Rating: 10 mph Horizontal
  • Nominal Spacing: 10 feet
  • Mounting: Suspended
  • Finish: Black or Stainless Steel
  • Manufactured: United States
  • Sunpak Heaters Warranty: One Year / Parts Only
  • Weight: 41 lbs


See More


Specifications

Heater Installation

Sunpak Heaters are intended to be installed by qualified personnel specifically trained and experienced in the installation of this type of heater and related system components. Some states or provinces require installation and service personnel to be licensed. If you state or province is such, be sure your contractor bears the appropriate license. Persons not qualified shall not attempt to install or repair this heater.

For Outdoor Use Only

Sunpak heaters are designed for outside use only. They are not for use in residential dwelling or other confined areas. Semi-enclosed patio are permissible provided they have adequate permanent openings around the patio periphery and meet the requirements for outdoors as defined in the installation instructions.

Clearance from Combustible Materials

Sunpak heaters all require a minimum distance from walls and ceilings. This is an important consideration for your design. The S34 will require greater clearances than the S25. The clearance also changes with the mounting angle. Refer to instructions for details

NOTE: Different Clearance Requirements for S34 & S25
Comfort Level

Typically you can expect the radiant heat to spread about 10 feet in each direction increasing the comfort level 5-10 deg F. outdoors.

Ventilation

Sunpak Heaters require adequate combustion air and ventilation to operate safely and efficiently. This requires openings above and below the level of the heater. Refer to the heater instructions for more detail.

Electrical Requirements

Sunpak® Heaters come with a 24 VAC spark ignition system which includes flame monitoring through flame rectification. All Sunpak S34 & S25 heaters with standard controls require an external 24 VAC Transformer. Transformer should never be placed inside the heater.

Gas Pressure

Sunpak® Heaters require a minimum inlet pressure of 6″ water column for natural gas and 11″ water column for propane gas. Gas pressure should never exceed 1/2 PSI or 14″ water column. For gas pressures exceeding 1/2 PSI a high-pressure regulator is required before the gas enters the heater.

Agency Certification

Sunglo heaters are design certified by the CSA under the ANSI Z83.19 standard

Heater Gas Conversion

The factory does not support converting heaters to different gases. Each heater has been setup and tested for a specific gas type. Please make sure you select the correct gas type, Natural or Propane gas, before making your purchase.