Foster™ - Foster® CP-211 CHIL-BRIDGE™ Bridging Encasement/Encapsulant Coating

DOWNLOADS

CHIL- BRIDGETM Bridging Encasement/ Encapsulant Coating CHIL-BRIDGE CP-211 bridging encasement/ encapsulant is a polymeric, water-based coating used to protect and isolate asbestos containing materials (ACM). It can be used in both indoor and outdoor applications. Used over all forms of ACM, it effe


Category: asbestos abatement | encapsulants | high-performance coatings...

MasterFormat: Asbestos Remediation | Asbestos Abatement | Painting and Coating...


Related Products

Overview


Foster® CP-211 CHIL-BRIDGE™ Bridging Encasement/Encapsulant Coating



CHIL- BRIDGETM Bridging Encasement/ Encapsulant Coating CHIL-BRIDGE CP-211 bridging encasement/ encapsulant is a polymeric, water-based coating used to protect and isolate asbestos containing materials (ACM). It can be used in both indoor and outdoor applications. Used over all forms of ACM, it effectively bridges, encases, and seals friable asbestos fibers.

CHIL-BRIDGE CP-211 bridging encasement/encapsulant coating is applied over ACM when bridging encapsulation has been determined to be the most appropriate asbestos abatement control method, and when complete removal of asbestos containing materials is not practical due to inaccessibility or other existing limitations. CHIL-BRIDGE CP-211 bridging encasement/encapsulant coating is applied to previously encapsulated ACM on piping, fittings, ductwork, and equipment.

CHIL-BRIDGE bridging encasement/encapsulant coating seals and bonds to ACM and to adjacent surfaces and materials. Once dry, the resultant film is tough, durable, and pliable; it will prevent damage due to mechanical abuse in the removal efforts, which could allow asbestos fibers to become airborne. The encasement/encapsulant coating permits ACM to be handled more efficiently and safely.

CHIL-BRIDGE meets the requirements of NFPA 90A and 90B 25/50 requirements.

Meets requirements for LEED IEQ 4.2 Low-Emitting Materials, Paints and Coatings. VOC: 40 g/l, less water and exempt solvents.

LIMITATIONS
Protect from freezing until dry. Do not store over 100°F (38°C). Do not apply below 40°F (4°C) or to surfaces operating at, or intended to operate in, excess of 200°F (93°C) . Not recommended for outdoor horizontal surfaces having a pitch of less that 1/2 inch (4 cm/m) per lineal foot.

Not suggested for use on floors.


COLOR:
CP - 211 White CP - 211-3 Blue Other colors available on special order.

APPLICATION CONSISTENCY:
Brush or Spray

WEIGHT PER GALLON (ASTM D-1475):
10.9 pounds (1.31 kg/liter)

AVERAGE NON-VOLATILE (ASTM D-1644):
66% by volume (74% by weight)

SERVICE TEMPERATURE LIMITS (FSTM 70):
(Temperature to which dry film is subjected.) 20ºF to 200ºF (-29ºC to 93ºC)

DRYING TIME (ASTM D-1640):
(Drying time will vary depending upon film thickness, temperature and humidity.) To Touch: 2 hours Through: 24-36 hours

COVERAGE:
2.4 U.S. gal./100 sq. ft. (1.0 l/sq. m.) Varies by substrate and membrane.

SAFETY:
Wet Flammability (ASTM D-3278) No Flash to Boiling (210°F/99°C) Surface Flame Spread (ASTM E-84) Flame Spread -- 10 Smoke Developed -- 40
Applied to 1/4 inch (6.4 mm) inorganic, reinforced cement board at a coverage rate of 6 galllons/100 sq. ft. (2.44 liters/sq. m). The flame spread may vary at different product thicknesses and/or when applied over surfaces other than inorganic, reinforced cement board.

CHIL-BRIDGE
contains no asbestos, lead, mercury, or mercury compounds. TM TradeMark of H.B. Fuller Construction Products Inc.

Visit us on the web at www.fosterproducts.com


See More


Sweets app for Revit – Learn More