Foster™ -Foster® 32-14 HIGH VELOCITY DUCT SEALANT

DOWNLOADS

FOSTER HIGH VELOCITY DUCT SEALANT FOSTER HIGH VELOCITY DUCT SEALANT is a fast setting, elastomeric compound designed as a joint sealant for high velocity air conditioning ducts installed indoors. It may be used with or without reinforcing tapes. It has a mild "paint type" odor and applies


Category: construction sealants | duct sealants | elastomeric sealants...

MasterFormat: Joint Protection | Joint Sealants | HVAC Air Distribution...


Related Products

Overview


Foster® 32-14 HIGH VELOCITY DUCT SEALANT



FOSTER HIGH VELOCITY DUCT SEALANT

FOSTER HIGH VELOCITY DUCT SEALANT is a fast setting, elastomeric compound designed as a joint sealant for high velocity air conditioning ducts installed indoors. It may be used with or without reinforcing tapes. It has a mild "paint type" odor and applies cleanly without stringing. Mechanical fasteners of the type and number normally used for duct assemblies are required to provide rigidity to the duct system.

HIGH VELOCITY DUCT SEALANT that can be used to adhere duct fabrics and flexible tubing runouts to high velocity ducts and to mixing boxes or air diffuser heads.

HIGH VELOCITY DUCT SEALANT meets NFPA 90A & 90B 25/50 requirements.

HIGH VELOCITY DUCT SEALANT is produced under the classification and follow- up service of Underwriter's Laboratories, Inc.

HIGH VELOCITY DUCT SEALANT will meet all SMACNA pressure classes up to 10" w.g. and SMACNA seal classes A, B, and C on ducts constructed to SMACNA standards.

HIGH VELOCITY DUCT SEALANT meets requirements for LEED IEQ 4.1 Low-Emitting Materials, Adhesives and Sealants. Sealant ­ Other per SMACNA TRB #9-09. VOC: 408 g/l, less water and exempt solvents.

HIGH VELOCITY DUCT SEALANT contains no asbestos, lead, mercury, or mercury compounds.

LIMITATIONS
Store and apply between 40ºF (4ºC) and 100ºF (38ºC). Always test plastic materials for compatibility when using a solvent base product. Systems may be pressure-tested 36 hours after application, above 60ºF (16ºC). Make certain this product is completely dry and the area free from solvent odor is food is involved. For outdoor application select SAFETEE Duct Sealant 32-17, 32-19, or top-coat 32-14 with a UV resistant finish.




COLOR:
Gray

APPLICATION CONSISTENCY:
Brush, caulking gun, or power extrusion

AVERAGE WEIGHT / U.S. GALLON (FSTM 3):
9.0 lbs. (1.1 kg/l)

AVERAGE NON-VOLATILE (FSTM D 1644):
43% by volume (63% by weight)

COVERAGE RANGE:
Brush: 35-50 sq. ft. / gal. (0.9 ­ 1.2 m2 /l) 0.032 to 0.046 in. (0.8 - 1.2 mm) wet film thickness. Caulking Gun: 125 lineal ft. per 10.5 fluid oz. tube, 1/8 in. bead. (38 m per .31 tube, 3.2 mm bead.) 30 lineal ft. per 10.5 fluid oz. tube, 1/4 in. bead. (9 m per .31 tube, 6.4 mm bead.)

SERVICE TEMPERATURE LIMITS (FSTM 70):
(Temperature at coated surface) -10ºF to 200ºF (-23ºC to 93ºC)

DRYING TIME 75ºF (24ºC) 50% RH:
Set to Touch: 2 hours
Dry Through: 36 hours

FUNGAL GROWTH RESISTANCE (ASTM G 21):
Rating = 0, no fungal growth on surface.

WET FLAMMABILITY (ASTM D 3278):
Flash point less than 20ºF (-7ºC)

SHORE HARDNESS (ASTM D 2240):
Type A: 63

SURFACE BURNING CHARACTERISTICS (ASTM 84):
Flame Spread: 0
Smoke Developed: 10 Tested as applied in two 2" wide strip s spaced 8 in. on center at a coverage of 26.7 ft 2 /gal.
Applied to 1/4 inch (6.4 mm) inorganic reinforced cement board. The flame spread may vary at different product thicknesses and/or when applied over other surfaces. TM Tradema rk of HB Fuller Construction Products Inc.

Visit us on the web at www.fosterproducts.com


See More


Sweetsstakes