DuraVent -DuraSeal® Special Gas Vent Boiler Adapters

DOWNLOADS

Quality and Dependability

The DuraSeal® flue is manufactured from either 316L or AL29-4C, a super-ferritic stainless steel designed for extreme resistance to chloride ion pitting, crevice corrosion and stress corrosion cracking.


Category: double-wall vent stacks | gas vent pipes | stainless steel vent pipes...

MasterFormat: Central Heating Equipment | Breechings, Chimneys, and Stacks | Fabricated Stacks...



DuraVent
877 Cotting Ct.
Vacaville, CA 95688
Tel: (800) 835-4429
Fax: (707) 446-4740

customerservice@duravent.com

https://duravent.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


DuraSeal® Special Gas Vent Boiler Adapters

Quality and Dependability

The DuraSeal® flue is manufactured from either 316L or AL29-4C, a super-ferritic stainless steel designed for extreme resistance to chloride ion pitting, crevice corrosion and stress corrosion cracking, as well as general corrosion in oxidizing and moderately reducing environments. AL29-4C and 316L are the ideal choice for withstanding the harmful effects of corrosive condensates created by partially or fully condensing high-efficiency natural gas and propane-fired heating appliances.

The Canadian Gas Research Institute found that test results proved AL29-4C to be one of the two “most corrosion-resistant alloys of 20 candidate stainless steels evaluated for resistance to chloride-induced corrosion in condensing and partially condensing gas-fired appliances.”

Stringent Standards for Quality Assurance.

To guarantee a perfect fit every time and to avoid built-in stress points or weak areas, tube ends are formed under stringent guidelines and held to exacting standards.

The casing (outer tube on DuraSeal DSD/DSID) is manufactured from type 441 stainless steel to provide long-lasting performance and stability when exposed to the outdoors.

The air space between the flue and casing is 1″ on DSD and 2″ insulated on DSID, providing close clearances to combustibles, reasonable outside dimensions and an additional heat shield or margin of safety where needed.

Built to Last

DuraSeal® features a smooth weld seam inside and out, which is completely shielded during the welding process. Contamination or molecular changes in the weld seam are avoided and no fillers are used in the welding process.

The DuraSeal® double-wall system is fully interchangeable with our DuraSeal® single-wall system. Both have been conformed to UL1738 and certified to ULC-S636 safety standards. When installed according to DuraVent’s installation instructions, DuraSeal® meets all test requirements for horizontal and vertical, interior or exterior installations. DSID features the same construction as DSD, but with 2″ air space filled with mineral wool insulation.

Specifications

Applications

DuraSeal® single wall (DS 3″-24″, DSLS 26″-36″) or double wall (DSD 3″-24″, DSLD 26″-36″) is a special stainless steel vent system for gas fired appliances listed as Catefory I, II, III, and IV or in Canada as Type BH Gas Venting as noted in ULC-636, with a maximum operating temperature of 550°F (288°C), and a maximum rated positive pressure of 35″ water column. It can also vent listed gas or oil fired appliance rated to be vent with TYPE L low temperature venting system (DSD & DSID only). DuraSeal® must be installed by an experienced professional familiar with the operation and maintenance of heating appliances and venting. Before installing this product, examine all components for possible shipping damage and read the complete installation manual. Failure to follow proper installation procedures, including vent pitch and improper appliance connections, may cause unsafe conditions.

Diameters

3″-36″

Listings

UL-1738/UL-1777/ULC-S636


See More


Specifications

Materials and Construction
DuraSeal Single Wall
DuraSeal Double Wall