Cathedral Stone Products, Inc. -Heavy Duty Rust Remover (MasonRE Heavy Duty Rust Remover) - 5 Gallon

DOWNLOADS

5 gallon
SKU # 1037

Availability: In stock


Category: efforescence removers | masonry maintenance | rust removers...

MasterFormat: Maintenance of Concrete | Common Work Results for Concrete | Cast-In-Place Concrete...



Cathedral Stone Products, Inc.
7266 Park Circle Dr.
Hanover, MD 21076
Tel: (410) 782-9150

info@cathedralstone.com

https://www.cathedralstone.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


Heavy Duty Rust Remover (MasonRE Heavy Duty Rust Remover) - 5 Gallon

5 gallon
SKU # 1037

Availability: In stock

The masonRE Light Duty Rust Remover is a gel based cleaner intended for the removal of rust staining, and efflorescence, on concrete, sandstone, unpolished granite, brick, concrete, limestone, marble and brownstone, brick etc.

Features and Benefits
  • Short dwell time

  • Gel clings to vertical surfaces and aids in clean up

  • Brush, roll or spray apply

  • User friendly

Application Procedures

Test Area
Always prepare a test area prior to full application. This will indicate the time required for project completion and suitability of product for effective cleaning of the substrate. Additionally, specific jobsite consumption rates can be calculated after the test area is completed.

Equipment & Tools
This product is designed to be applied by spray, brush or roller. Other equipment required: masking tape, plastic (polyethylene) sheet, should be used for protecting surfaces not to be treated with masonRE Light Duty Rust Remover.

Preparation
MASKING: Cover / protect areas where cleaning is not desired, including adjoining surfaces where over spray may travel. Plastic (polyethylene) sheets make a very effective barrier. Test to see affects on any glass or metals that may come in contact with masonRE Light Duty Rust Remover.

Application
Apply a thick, even layer of masonRE Light Duty Rust Remover onto a wet/damp substrate. Use a nylon brush to scrub very dirty areas.

Dwell Time
The time required for the masonRE Light Duty Rust Remover to adequately clean a typical substrate is approximately 10 to 20 minutes. If the rust is extremely thick masonRE Light Duty Rust Remover may be left on the substrate for 4 to 6 hours. If product begins to dry a second layer of product may be applied directly over the existing one. Apply test panels to determine the dwell time prior to full application of product. DO NOT ALLOW TO DRY ON SUBSTRATE.

Removal and Cleanup
After allowing the product to dwell, rinse the surface with copious amounts water (pressure washer). Do not allow run off to dry on other surfaces.

Safety Requirements
Proper safety procedures should be followed at all times while handling this product. Refer to the Material Safety Data Sheet for important health/safety information before use. MasonRE Light Duty Rust Remover should only be used for approved applications.

Limitations

Surface temperatures should be 40° to 90°F (5° to 32°C). The product performs effectively at lower temperatures (even at 40°F, 5°C), but the dwell time increases.

Packaging and Coverage
Packaging: Approximately 5 gallons

Always test the substrate to ensure accurate coverage rates. Typical coverage rates are between 150 and 200 ft sq. ft. per gallon.

DO NOT ALLOW PRODUCT TO FREEZE!
THE ABOVE PROCEDURES ARE SIMPLY GUIDELINES FOR TESTING, APPLICATION, RINSING AND CLEANUP. BEFORE TESTING OR USING MASONRE LIGHT DUTY RUST REMOVER CHECK WITH LOCAL, STATE, AND FEDERAL REGULATIONS TO ENSURE THE PRODUCT IS BEING USED PROPERLY AND THERE ARE NO VIOLATIONS OF THE LAW.

Notice: The information contained herein is based on our own research and the research of others, and it is provided solely as a service to help users. It is believed to be accurate to the best of our knowledge. However, no guarantee of its accuracy can be made, and it is not intended to serve as the basis for determining this product"s suitability in any particular situation. For this reason, purchasers are responsible to make their own tests and assume all risks associated with using this product.


See More


Specifications

Technical Data
AppearanceWhite foam gel
Specific Gravity1
Boiling PointNot specified
pH2.0
VOC content0%
Sweetsstakes