Acoustical Surfaces, Inc. -C - CIP - CIW Neoprene Housed Spring Mounts

DOWNLOADS

C Housed Spring Isolator Mounts may be used on outdoor applications. These vibration isolation spring mounts have lateral stability and are recommended for moderate horizontal wind loads without seismic restraint requirements.


Category: HVAC vibration and seismic control | isolation mounts | manufactured seismic control components...

MasterFormat: Manufactured Sound and Vibration Control Components | Manufactured Seismic Control Components | Common Work Results for HVAC...



Acoustical Surfaces, Inc.
123 Columbia Court North Suite 201
Chaska, MN 55318
Tel: (800) 470-6652
Fax: (952) 448-2613

sales@acousticalsurfaces.com

https://www.acousticalsurfaces.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


C - CIP - CIW Neoprene Housed Spring Mounts

C Housed Spring Isolator Mounts may be used on outdoor applications. These vibration isolation spring mounts have lateral stability and are recommended for moderate horizontal wind loads without seismic restraint requirements.

“C” one inch minimum deflection spring isolator mounts provide greater vibration control than the lower deflection neoprene mounts. These vibration isolation spring mounts function the same as SLF mounts but have semi-circular neoprene sponge inserts that limit movement due to start and stop and horizontal wind load. These spring isolator mounts prevent contact between the projections of the upper and lower semi-circular casting. C spring vibration isolation spring mounts are recommended for all air-conditioning applications, under compressors, air handling units, centrifugal fans and most other constant frequency vibration problems.

“C” two inch deflection spring isolator mounts are for use on equipment located on wide upper level building spans and roofs where more than one inch of deflection is needed to cancel the effect of the building spans deflection.

CIP - House Spring Mounts with Internal Adjustment

CIW - House Spring Mounts with Internal Adjustment and W Pad

Height Saving Bracket - Use when equipment cannot be raised to mount’s free & operating height.

Installation:

Supporting surfaces must be flat and level under vibration isolation spring mounts. Relative elevations must be held to ½″ from the highest to the lowest position. Grout or provide full spacers to compensate for larger differences.

  1. When equipment is mounted directly to Type “C” Mounts, place mountings under equipment bolt holes and install the mounting adjustment bolts as shown.

    • When equipment is installed directly to Type “CI”, “CIP” or “CIW” Mounts, place mounting under the equipment holes or in the proper position.

    • When vibration isolation spring mounts are installed under steel base mounting brackets, block the base at the proper elevation as shown on the drawing before installing mounts.

  2. Take 2 complete downward (clockwise) turns on adjustment bolt or internal adjustment nut of all spring isolator mounts. Repeat this procedure as many times as necessary until clearance “A” is a minimum of ¼″ for direct mounting or equipment lifts off blocks.

  3. Level equipment by taking additional turns on low side or corner.

  4. On Type “C” Mounts, Tighten lock nut against equipment base.

All springs have additional travel to solid equal to 50% of the rated deflection except C-B2-450, which has minimum 38% at rated capacity.


See More


Specifications

C 1" Deflection Spring Mounts
Type & SizeRated CapacityRated DeflectionMount ConstantSpring Color/StripeDimensionsDimensionsDimensionsDimensions
Type & SizeRated CapacityRated DeflectionMount ConstantSpring Color/StripeALWFree & Oper. Height
C-A-4545 lbs1.60″28 lbs/inBlue4″5-3/4″2-1/8″4-1/2″
C-A-7575 lbs1.50″50 lbs/inOrange4″5-3/4″2-1/8″4-1/2″
C-A-125125 lbs1.33″94 lbs/inBrown4″5-3/4″2-1/8″4-1/2″
C-A-200200 lbs1.15″174 lbs/inBlack4″5-3/4″2-1/8″4-1/2″
C-A-310310 lbs1.00″310 lbs/inYellow4″5-3/4″2-1/8″4-1/2″
C-A-400400 lbs1.00″400 lbs/inGreen4″5-3/4″2-1/8″4-1/2″
C-A-510510 lbs1.00″510 lbs/inRed4″5-3/4″2-1/8″4-1/2″
C-A-625625 lbs1.00″625 lbs/inWhite4″5-3/4″2-1/8″4-1/2″
3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection3/4″ Minimum Deflection
C 2" Deflection Spring Mounts
Type & SizeRated CapacityRated DeflectionMount ConstantSpring Color/StripeDimensionsDimensionsDimensionsDimensions
Type & SizeRated CapacityRated DeflectionMount ConstantSpring Color/StripeALWFree & Oper. Height
C-B-2020 lbs2.40″8 lbs/inTan5-3/4″8-1/4″2-3/4″5-3/4″
C-B-2626 lbs2.18″12 lbs/inWhite/Blue5-3/4″8-1/4″2-3/4″5-3/4″
C-B-3535 lbs2.20″16 lbs/inPurple5-3/4″8-1/4″2-3/4″5-3/4″
C-B-5050 lbs2.20″24 lbs/inWhite/Red5-3/4″8-1/4″2-3/4″5-3/4″
C-B-6565 lbs2.10″31 lbs/inBrown5-3/4″8-1/4″2-3/4″5-3/4″
C-B-8585 lbs2.10″40 lbs/inWhite/Black5-3/4″8-1/4″2-3/4″5-3/4″
C-B-115115 lbs2.00″57 lbs/inSilver5-3/4″8-1/4″2-3/4″5-3/4″
C-B-150150 lbs2.00″75 lbs/inOrange5-3/4″8-1/4″2-3/4″5-3/4″
C-B2-210210 lbs2.12″99 lbs/inSilver5-3/4″8-1/4″2-3/4″5-3/4″
C-B2-290290 lbs2.00″144 lbs/inBlue5-3/4″8-1/4″2-3/4″5-3/4″
C-B2-450450 lbs2.00″224 lbs/inTan5-3/4″8-1/4″2-3/4″5-3/4″
1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection1-1/2″ Minimum Deflection