![]() ![]() TRACO Bevel Casement
TRACO TR-410 Casement Outswing
TRACO TR-420 Casement Inswing
The following items are provided below:
For half scale details and information on other TRACO products, please contact your TRACO Architectural Consultant via phone (1-800-837-7002), fax (724-776-7014), or e-mail (archservices@traco.com). [A] TRACO TR-410 Product Description Bevel Casement Outswing Thermal Aluminum Window TR-410 Outswing Heavy Commercial C-HC65 BENEFITS Strength
Durability
STANDARDS
OPTIONS
[B] TRACO TR-410 C-HC65 Specification *TO FINISH SPECIFICATION:1. Read then delete comments in *stars*. 2. Add or delete options in (parentheses). 3. Replace preceding standards with options in [brackets] or delete options in [brackets]. 4. Revise paragraph numbers and/or letters, as necessary.* PART 1 - GENERAL 1.01 SECTION INCLUDES A. Material: aluminum windows as on the drawings and specified in this section. B. Installation: labor, tools, and material needed to install aluminum windows. C. Glass and glazing. (1.02 PRODUCTS FURNISHED BUT
NOT INSTALLED)
(1.03 PRODUCTS INSTALLED BUT NOT FURNISHED)
1.04 RELATED SECTIONS - Section 07900 - Sealants 1.05 REFERENCES A. AAMA - American Architectural Manufacturers Association
B. ASCA - Architectural Spray Coaters Association - ASCA 96 Voluntary Specification for Superior Performance of Organic Coatings on Architectural Aluminum Curtainwall, Extrusions and Miscellaneous Aluminum Components C. ASTM - American Society for Testing and Materials
1.06 SYSTEM DESCRIPTION A. AAMA Designation: C-HC65. B. Windows: 3-1/4" frame depth; extruded aluminum with integral structural polyurethane thermal break; vent flush with frame; vent with exterior bevel; equal-leg standard [narrow] frame; one finish type and color [one exterior finish type and color, and one interior finish type and color] factory-applied; factory-assembled. C. Configuration: casement outswing; single vent [single vent and fixed] [multiple vents] [multiple vents and fixed] per frame. D. Vent glazing: exterior tape; 1" insulating glass [or single lites]; EPDM gasket; interior aluminum glazing bead; glass description in paragraph 2.04; factory-glazed. [D. Vent dual glazing: exterior tape; maximum 1/4" exterior lite; internal EPDM gasket; (blinds;) maximum 1/4" interior lite in PVC gasket in panel removable with 1/8" hex pin key; glass description in paragraph 2.04; factory-glazed.] (E. Fixed glazing: exterior tape; 1" insulating glass [or single lites]; EPDM gasket; interior aluminum glazing bead; glass description in paragraph 2.04; factory-glazed.) 1.07 PERFORMANCE REQUIREMENTS A. Conformance to C-HC65 specifications in AAMA/NWWDA 101/I.S.2-97 when tests are performed on a 2'0" x 4'0" minimum frame size with the following test results:
B. Thermal testing per AAMA 1503-98, at the prescribed 4'0" x 6'0" test size glazed with 1 insulating glass made with 1/8 clear and 1/8 Low E lites and argon gas, with the following test results:
1.08 SUBMITTALS A. Shop drawings: window location chart; typical window elevations; details of assemblies, hardware, and glazing details for factory-glazed units. B. Product data: manufacturer's specifications and test reports from an AAMA-accredited laboratory. C. Samples: each specified finish for aluminum; other samples as requested. 1.09 QUALITY ASSURANCE A. Submit for prebid approval ten days prior to bid opening a sample window representing the bid window except for color and valid test reports from an AAMA-accredited laboratory conforming to test results in Paragraph 1.07. B. Acceptance will be by addendum only as no verbal approvals will be allowed. C. Submit bid on prequalified products in prebid written addendum. Bidder must identify manufacturer and model of product on which the bid is based. D. Furnish a valid AAMA Notice of Product Certification indicating that the windows for the project conform to AAMA/NWWDA 101/I.S.2-97. E. Furnish visible, permanent IGCC certification labels for the CBA rating level on dual-seal double insulating glass units. F. Manufacturer's warranties:
...DURANAR™ organic finish conforming to ASCA 96 and AAMA 2605-98: warrant for fifteen years against chipping, peeling, cracking, chalking, or fading. *Or enter the following for an AAMA 2604 durable acrylic paint finish* ...ACRYNAR™ organic finish conforming to AAMA 2604-98: warrant for ten years against chipping, peeling, cracking, chalking, or fading. *Or enter the following for an AAMA 2603 acrylic paint finish* ...DURACRON™ organic finish conforming to AAMA 2603-98: warrant for five years against chipping, peeling, or cracking. (G. Project Survey: *Contact TRACO to register before project bid date* by installer and manufacturers representatives; one year after date of completion; to recommend maintenance procedures.) 1.10 DELIVERY, STORAGE, AND HANDLING - Handle and protect windows and accessories in accordance with AAMA CW-10-97 until project completion. PART 2 - PRODUCTS 2.01 MANUFACTURERS A. TRACO TR-410 Casement Outswing Thermal Aluminum Window B. Other acceptable manufacturers who have demonstrated a successful history of manufacturing for *Enter number* years equivalent products:
2.02 MATERIALS A. Aluminum extrusions: produced from commercial quality 6063-T5 alloy; free from defects impairing strength and durability. B. Hardware: exposed white bronze butt hinges to rotate vent outward on vertical axis; white bronze cam handles and strikes; roto operator conforming to AAMA 901.1-90; (stainless steel limit arm with release key). C. Weatherstrip: secured in extruded ports; double rows on vent perimeter of offset bulb gasket utilizing a Neoprene foam rod for dimensional stability, a Santoprene cover for weather resistance, and a polycarbonate base for shrinkage resistance; continuous around vent corners with butt joint bonded with silicone sealant. (D. Blinds: 1" x .008" aluminum slats; slat color chosen from manufacturer's standards; tilt adjusted with interior tilt control knob.) (E. Screens: full; field-mounted on interior with swivel clips; handle-access wickets; 3/4" x 1 1/8" x .050" extruded tubular aluminum frame with finish to match window in color and performance; corners mitered, gusset reinforced, and crimped; 18 x 16 dark fiberglass [aluminum] mesh; PVC spline.) 2.03 FABRICATION A. Frame: tubular members; corners mitered, gusset reinforced, and crimped. B. Vent: tubular members; corners mitered, gusset reinforced, and crimped. C. Frame and vent joints: factory-sealed with sealant conforming to AAMA 800-92. D. Water control: compression gasket on vent interior to utilize pressure equalization and to allow water to drain by gravity. 2.04 DOUBLE INSULATING GLASS UNITS A. Construction
B. Exterior glass lite
C. Interior glass lite
D. Performance
[2.04 TRIPLE INSULATING GLASS UNITS] A. Construction
B. Exterior glass lite
C. Internal film: Southwall Heat Mirror™ #SC75. D. Interior glass lite
(E. Performance: *Enter U value, etc., information as required*) [2.04 MONOLITHIC VISION LITES] A. Thickness: 1/8" [3/16"] [1/4"]. B. Tint: clear [bronze] [gray] [pattern #62 obscure]. C. Type: annealed [tempered] [laminated *Enter interlayer and lite description*] [heat-strengthened] [1/4 " clear wired *Enter pattern*] [polycarbonate *Enter description*]. (D. Coating: solar-reflective [pyrolitic Low E on #2 surface].) (E. Performance: *Enter transmittance information as required*) 2.05 FINISH ON ALUMINUM EXTRUSIONS *Enter Para. 2.05 twice if different finishes on exterior and interior option is desired* A. Application: on clean extrusions free from serious surface blemishes; on exposed surfaces visible when installed product's operating sash are closed. *Enter the following for an ASCA 96/AAMA 2605 fluoropolymer paint finish* B. Coating: PPG DURANAR™ with resin containing 70% fluoropolymer; thermosetting; alternative finishes will not be acceptable. C. Quality standard: conforming to ASCA 96 and AAMA 2605-98, including 10 years Florida exposure and 4000 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: minimum one primer coat and one color coat. G. Dry film thickness: minimum 1.2 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 2604 durable acrylic paint finish* B. Coating: PPG ACRYNAR™ with durable acrylic resin; thermosetting; alternative finishes will not be acceptable. C. Quality standard: conforming to AAMA 2604-98, including 5 years Florida exposure and 3000 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: minimum one primer coat and one color coat. G. Dry film thickness: minimum 1.4 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 2603 acrylic paint finish* B. Coating: PPG DURACRON™ with acrylic resin; thermosetting. C. Quality standard: conforming to AAMA 2603-98, including 1 year Florida exposure and 1500 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: one color coat. G. Dry film thickness: minimum .8 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 611 clear anodize finish* B. Coating: clear anodize. C. Quality standard: conforming to AAMA 611-98. D. Thickness: AAM10C22A41 Class I - .7 mils #215 [AAM10C22A31 Class II - .4 mils #204]. *Or enter the following for an AAMA 611 color anodize finish* B. Coating: color anodize. C. Quality standard: conforming to AAMA 611-98. D. Thickness: AAM10C22A44 Class I - .7 mils. E. Color: #313 dark bronze [#311 light bronze] [#312 medium bronze] [#315 black]. (2.06 INSTALLATION ACCESSORIES) *Enter the following only when the standard TR-410 frame is used** B. Material: extruded aluminum; nominal .062 wall; with exposed surfaces finished to match window color and finish performance; concealed fasteners; required weatherseals; designed for unrestricted expansion and contraction. C. Exterior: (two-piece mullion cover;) (two-piece head and jamb receptor with thermal break;) (subsill with thermal break and end dams;) (sill cover;) (slip-on expanders). D. Interior: (two-piece snap trim;) (stool cover). E. Mullions: with thermal break; (stack;) (offset stack;) (three-piece). PART 3 - EXECUTION 3.01 PREPARATION - Prepare openings to be in tolerance, plumb, level, provide for secure anchoring, and in accordance with approved shop drawings. 3.02 INSTALLATION A. Install windows in accordance with manufacturer's recommendations and approved shop drawings with skilled craftspeople who have demonstrated a successful history of installing windows for *Enter number* years. B. Provide required support and securely fasten and set windows plumb, square, and level without twist or bow. C. Apply sealant per sealant manufacturer's recommendations at joints, wipe off excess, and leave exposed sealant surfaces clean and smooth. (3.03 FIELD TESTING) A. Test installed units in conformance with AAMA 502-90 for air and water infiltration with the window manufacturer, contractor, and owner present. B. Select test units as directed by the owner's representative and use an AAMA-accredited laboratory provided by the owner or contractor. 3.04 ADJUSTING AND CLEANING - Adjust windows as necessary for smooth and weathertight operation, and leave windows clean and free of construction debris. [C] TRACO TR-420 Product Description Bevel Casement Inswing Thermal Aluminum Window TR-420 Inswing Heavy Commercial C-HC65 BENEFITS Strength
Durability
STANDARDS
OPTIONS
[D] TRACO TR-420 C-HC65 Specification *TO FINISH SPECIFICATION:1. Read then delete comments in *stars*. 2. Add or delete options in (parentheses). 3. Replace preceding standards with options in [brackets] or delete options in [brackets]. 4. Revise paragraph numbers and/or letters, as necessary.* PART 1 - GENERAL 1.01 SECTION INCLUDES A. Material: aluminum windows as on the drawings and specified in this section. B. Installation: labor, tools, and material needed to install aluminum windows. C. Glass and glazing. (1.02 PRODUCTS FURNISHED BUT
NOT INSTALLED)
(1.03 PRODUCTS INSTALLED BUT
NOT FURNISHED)
1.04 RELATED SECTIONS - Section 07900 - Sealants 1.05 REFERENCES A. AAMA - American Architectural Manufacturers Association
B. ASCA - Architectural Spray Coaters Association - ASCA 96 Voluntary Specification for Superior Performance of Organic Coatings on Architectural Aluminum Curtainwall, Extrusions and Miscellaneous Aluminum Components C. ASTM - American Society for Testing and Materials
1.06 SYSTEM DESCRIPTION A .AAMA Designation: C-HC65. B. Windows: 3-1/4" frame depth; extruded aluminum with integral structural polyurethane thermal break; vent flush with frame; vent with exterior bevel; equal-leg standard [narrow] frame; one finish type and color [one exterior finish type and color, and one interior finish type and color] factory-applied; factory-assembled. C. Configuration: casement inswing; single vent [single vent & fixed] [multiple vents] [multiple vents & fixed] per frame. D. Vent glazing: exterior tape; 1" insulating glass [or single lites]; EPDM gasket; interior aluminum glazing bead; glass description in paragraph 2.04; factory-glazed. [D. Vent dual glazing: exterior tape; maximum 1/4" exterior lite; internal EPDM gasket; (blinds;) maximum 1/4" interior lite in PVC gasket in panel removable with 1/8" hex pin key; glass description in paragraph 2.04; factory-glazed.] (E. Fixed glazing: exterior tape; 1" insulating glass [or single lites]; EPDM gasket; interior aluminum glazing bead; glass description in paragraph 2.04; factory-glazed.) 1.07 PERFORMANCE REQUIREMENTS A. Conformance to C-HC65 specifications in AAMA/NWWDA 101/I.S.2-97 when tests are performed on a 20 x 4'0" minimum frame size with the following test results:
B. Thermal testing per AAMA 1503-98, at the prescribed 4'0" x 6'0" test size glazed with 1 insulating glass made with 1/8 clear and 1/8 Low E lites and argon gas, with the following test results:
1.08 SUBMITTALS A. Shop drawings: window location chart; typical window elevations; details of assemblies, hardware, and glazing details for factory-glazed units. B. Product data: manufacturer's specifications and test reports from an AAMA-accredited laboratory. C. Samples: each specified finish for aluminum; other samples as requested. 1.09 QUALITY ASSURANCE A. Submit for prebid approval ten days prior to bid opening a sample window representing the bid window except for color and valid test reports from an AAMA-accredited laboratory conforming to test results in Paragraph 1.07. B. Acceptance will be by addendum only as no verbal approvals will be allowed. C. Submit bid on prequalified products in prebid written addendum. Bidder must identify manufacturer and model of product on which the bid is based. D. Furnish a valid AAMA Notice of Product Certification indicating that the windows for the project conform to AAMA/NWWDA 101/I.S.2-97. E. Furnish visible, permanent IGCC certification labels for the CBA rating level on dual-seal double insulating glass units. F. Manufacturer's warranties:
*Enter the following for an ASCA 96/AAMA 2605 fluoropolymer paint finish* ...DURANAR™ organic finish conforming to ASCA 96 and AAMA 2605-98: warrant for fifteen years against chipping, peeling, cracking, chalking, or fading. *Or enter the following for an AAMA 2604 durable acrylic paint finish* ...ACRYNAR™ organic finish conforming to AAMA 2604-98: warrant for ten years against chipping, peeling, cracking, chalking, or fading. *Or enter the following for an AAMA 2603 acrylic paint finish* ...DURACRON™ organic finish conforming to AAMA 2603-98: warrant for five years against chipping, peeling, or cracking. (G. Project Survey: *Contact TRACO to register before project bid date* by installer and manufacturers representatives; one year after date of completion; to recommend maintenance procedures.) 1.10 DELIVERY, STORAGE, AND HANDLING - Handle and protect windows and accessories in accordance with AAMA CW-10-97 until project completion. PART 2 - PRODUCTS 2.01 MANUFACTURERS A. TRACO TR-420 Casement Inswing Thermal Aluminum Window B. Other acceptable manufacturers who have demonstrated a successful history of manufacturing for *Enter number* years equivalent products:
2.02 MATERIALS A. Aluminum extrusions: produced from commercial quality 6063-T5 alloy; free from defects impairing strength and durability. B. Hardware: exposed white bronze butt hinges to rotate vent inward on vertical axis; white bronze cam handles and strikes (; stainless steel limit arm with release key). C. Weatherstrip: secured in extruded ports; double rows on vent perimeter of offset bulb gasket utilizing a Neoprene foam rod for dimensional stability, a Santoprene cover for weather resistance, and a polycarbonate base for shrinkage resistance; continuous around vent corners with butt joint bonded with silicone sealant. (D. Blinds: 1" x .008" aluminum slats; slat color chosen from manufacturer's standards; interior tilt control knob.) (E. Screens: full; field-mounted exterior tracks; two stainless steel leaf springs; 5/16" x 1 1/2" x .050" extruded tubular aluminum frame with finish to match window in color and performance; corners mitered, gusset reinforced, and crimped; 18 x 16 dark fiberglass [aluminum] mesh; PVC spline.) 2.03 FABRICATION A. Frame: tubular members; corners mitered, gusset reinforced, and crimped. B. Vent: tubular members; corners mitered, gusset reinforced, and crimped. C. Frame and vent joints: factory-sealed with sealant conforming to AAMA 800-92. D. Water control: pressure equalization gasket on vent interior; tubular sill with weeps, foam baffles, and flap covers to allow water to drain by gravity and resist wind-driven water. 2.04 DOUBLE INSULATING GLASS UNITS A. Construction
B. Exterior glass lite
C. Interior glass lite
D. Performance
[2.04 TRIPLE INSULATING GLASS UNITS] A. Construction
B. Exterior glass lite
C. Internal film: Southwall Heat Mirror™ #SC75. D. Interior glass lite
(E. Performance: *Enter U value, etc., information as required*) [2.04 MONOLITHIC VISION LITES] A. Thickness: 1/8" [3/16"] [1/4"]. B. Tint: clear [bronze] [gray] [pattern #62 obscure]. C. Type: annealed [tempered] [laminated *Enter interlayer and lite description*] [heat-strengthened] [1/4 " clear wired *Enter pattern*] [polycarbonate *Enter description*]. (D. Coating: solar-reflective [pyrolitic Low E on #2 surface].) (E. Performance: *Enter transmittance information as required*) 2.05 FINISH ON ALUMINUM EXTRUSIONS *Enter Para. 2.05 twice if different finishes on exterior and interior option is desired* A. Application: on clean extrusions free from serious surface blemishes; on exposed surfaces visible when installed product's operating sash are closed. *Enter the following for an ASCA 96/AAMA 2605 fluoropolymer paint finish* B. Coating: PPG DURANAR™ with resin containing 70% fluoropolymer; thermosetting; alternative finishes will not be acceptable. C. Quality standard: conforming to ASCA 96 and AAMA 2605-98, including 10 years Florida exposure and 4000 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: minimum one primer coat and one color coat. G. Dry film thickness: minimum 1.2 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 2604 durable acrylic paint finish* B. Coating: PPG ACRYNAR™ with durable acrylic resin; thermosetting; alternative finishes will not be acceptable. C. Quality standard: conforming to AAMA 2604-98, including 5 years Florida exposure and 3000 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: minimum one primer coat and one color coat. G. Dry film thickness: minimum 1.4 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 2603 acrylic paint finish* B. Coating: PPG DURACRON™ with acrylic resin; thermosetting. C. Quality standard: conforming to AAMA 2603-98, including 1 year Florida exposure and 1500 hours humidity tests. D. Pretreatment: five-stage; zinc chromate conversion coating. E. Application: electrostatic spray and oven bake by approved applicator. F. Coating quantity: one color coat. G. Dry film thickness: minimum .8 mils on exposed surfaces, except inside corners and channels. H. Color: chosen from manufacturer's standards. *Or enter the following for an AAMA 611 clear anodize finish* B. Coating: clear anodize. C. Quality standard: conforming to AAMA 611-98. D. Thickness: AAM10C22A41 Class I - .7 mils #215 [AAM10C22A31 Class II - .4 mils #204]. *Or enter the following for an AAMA 611 color anodize finish* B. Coating: color anodize. C. Quality standard: conforming to AAMA 611-98. D. Thickness: AAM10C22A44 Class I - .7 mils. E. Color: #313 dark bronze [#311 light bronze] [#312 medium bronze] [#315 black]. (2.06 INSTALLATION ACCESSORIES) *Enter the following only when the standard TR-420 frame is used* A. Material: extruded aluminum; nominal .062 wall; with exposed surfaces finished to match window color and finish performance; concealed fasteners; required weatherseals; designed for unrestricted expansion and contraction. B. Exterior: (two-piece mullion cover;) (two-piece head and jamb receptor with thermal break;) (subsill with thermal break and end dams;) (sill cover;) (slip-on expanders). C. Interior: (two-piece snap trim;) (stool cover). D. Mullions: with thermal break; (stack;) (offset stack;) (three-piece). PART 3 - EXECUTION 3.01 PREPARATION - Prepare openings to be in tolerance, plumb, level, provide for secure anchoring, and in accordance with approved shop drawings. 3.02 INSTALLATION A. Install windows in accordance with manufacturer's recommendations and approved shop drawings with skilled craftspeople who have demonstrated a successful history of installing windows for *Enter number* years. B. Provide required support and securely fasten and set windows plumb, square, and level without twist or bow. C. Apply sealant per sealant manufacturer's recommendations at joints, wipe off excess, and leave exposed sealant surfaces clean and smooth. (3.03 FIELD TESTING) A. Test installed units in conformance with AAMA 502-90 for air and water infiltration with the window manufacturer, contractor, and owner present. B. Select test units as directed by the owner's representative and use an AAMA-accredited laboratory provided by the owner or contractor. 3.04 ADJUSTING AND CLEANING - Adjust windows as necessary for smooth and weathertight operation, and leave windows clean and free of construction debris. For half scale details, other specifications, and information on other TRACO products, please contact your TRACO Architectural Consultant via phone (1-800-837-7002), fax (724-776-7014), e-mail (archservices@traco.com), or visit the TRACO web site (http://www.traco.com). TRACO |