Hohmann & Barnard, Inc.
30 Rasons Court
P.O. Box 5270
Hauppauge, NY 11788-0270
Telephone: (516) 234-0600
FAX: (516) 234-0683
Website: http://www.h-b.com/


WALL TIES AND ANCHORS

#303 – Corrugated Dovetail Brick Tie
#305 – Dovetail Slot
  • Mill galv./hot galv./stainless steel.
  • Standard #303 is 1 in. wide x 16 ga., 14 ga. or 12 ga. thick x 3 1/2 in. or 5 1/2 in. long. Other lengths and widths available upon request.
  • #305 Slot available in 26, 24, 22, 20, 18 or 16 ga. (26 and 24 ga. not available hot dip galv.)
  • Slots are standard 10 ft. lengths foam filled.

Important: We are not responsible for incompatibility if Ties or Slots are interchanged with those of other manufacturers.

#315 – Flexible Dovetail Brick Tie
  • Mill galv./hot galv./stainless steel.
  • Dovetail end is 16 ga. or 12 ga. thick x 1 in. wide (state preference when ordering).
  • Vee Wall Tie is 3/16 in. dia. x 3 in., 3 1/2 in., 4 in., 4 1/2 in., 5 in., 7 in. or 9 in. long (state size when ordering).
  • Other sizes upon request.

Dovetail head fits H & B #305 Anchor Slot. Compatibility with Dovetail Slots from other manufacturers is not guaranteed.

Permits horizontal and vertical movement of the masonry wall while restraining the wall from moving laterally out of its plane.

#315-BT – Flexible Dovetail Brick Tie
  • Fitted with a Byna-Tie® in lieu of a conventional Vee Wall Tie.
  • Finish and size same as #315 (Byna-Tie® available 2 1/2 in. thru 5 in. long).

For use with the Seismiclip® Interlock System. Compatibility with Dovetail Slots from other manufacturers is not guaranteed.

#344 – Rigid Partition Anchor
  • Plain steel/hot dip galv./stainless steel.
  • Made to order from 1/8 in., 3/16 in., 1/4 in. or 3/8 in. bar stock
  • Standard bends are 2 in. Other sizes available upon request.

For anchoring load bearing walls at intersections.

#345 – Corrugated Buck Anchor
  • Mill galv./hot dip galv./stainless steel.
  • Standard sizes: 1 1/4 in., 1 1/2 in. or 2 in. wide; 16 ga., 14 ga. or 12 ga. thick; 3 1/2 in. to 10 in. long.
  • Standard bend 2 in. long with or without nail holes.
  • Other sizes, holes or slots available upon request.

For anchoring new masonry to concrete, structural steel, existing masonry or door bucks.

#345-BT – Flexible Tie
  • Mill galv./hot dip galv./stainless steel.
  • Sheet steel is 3/4 in. wide x 12 ga. thick with 5/16 in. screw hole.
  • Byna-Tie® is 3/16 in. diameter x 2 1/2 in., 3 in., 3 1/2 in., 4 in., 4 1/2 in. or 5 in. long (state when ordering).
  • 1/4 in. diameter available on special request.

For use with the Seismiclip® Interlock System (where reinforced masonry walls are required).

#VWT – Vee Wall Tie
  • Mill galv./hot dip galv./stainless steel
  • 3/16 in. or 1/4 in. diameter wire.
  • Sizes:
    3 in. wide x 3 in. long
    3 1/2 in. wide x 3 1/2 in. long
    4 in. wide x 4 in. long
    4 1/2 in. wide x 4 1/2 in. long
    5 in. wide x 5 in. long
    7 in. wide x 7 in. long
    7 in. wide x 9 in. long
  • Other sizes upon request.

For use with H & B's DW-10 Series Anchors (tying brick veneer to steel studs), or H & B's #359 Series Weld-On Ties (tying masonry walls to steel columns).