Stone Anchors

Bent Anchors
No. 140 Z-Type Stone Anchor
No. 141 U-Type Stone Anchor
No. 143 Twisted-Type Stone Anchor
No. 144 L-Type Stone Anchor
No. 145 Split-Bend Stone Anchor
No. 147 Twisted Split-Bend Stone Anchor
No. 148 Flat Split-Bend Stone Anchor

Pin Anchors
No. 150 Flat-Type Stone Pin Anchor
No. 151 Corrugated Stone Pin Anchor
No. 152 L-Type Stone Pin Anchor
No. 152-A L-Type Stone Half-Pin Anchor
No. 152-S Split-Bend Stone Pin Anchor
No. 153 Flange Hook Stone Pin Anchor
No. 154 Two-Way Stone Pin Anchor
No. 154-A Double Half-Pin Stone Anchor
No. 157-A Dowel-Centered Pin Anchor

Screw-On Anchors
No. 274 Screw-On Split-Bend Anchor
No. 275-U U-Type Screw-On Anchor
No. 275-Z Z-Type Screw-On Anchor
No. 276 Pin-Type Screw-On Anchor
No. 295 Z-Type Slotted Screw-On Anchor
 
 
 

STONE AND MASONRY ANCHORS
Made to Order
Stone installation must be designed in accordance with acceptable engineering practices and the recommendations of the stone fabricator.
STRAP ANCHORS: Typical dimensions are 3/4" (19 mm) to 2" (51 mm) wide x 16 gage to 3/8" (9.5 mm) thick x length required.
PIN ANCHORS: Pins are available in diameters of 1/4" (6.35 mm), 3/16" (4.76 mm), 3/8" (9.5 mm), 1/2" (12.7 mm), 5/8" (15.875 mm), and 3/4" (19 mm). They typically are installed 1-1/2" (38 mm) into each stone. They can be furnished loose, fixed in place, or welded in place.
 
 

SPLIT BENDS: Recommended minimum width of split bend anchors is 1-1/4" (32 mm) wide. Length is usually a minimum of 3/4" (19 mm).
CORRUGATED ANCHORS: Maximum steel thickness is 3/16" (4.76 mm), 1/8" (3.17 mm) for stainless steel.
HOLES: Specify center spacing from designated end. Holes are typically 1/16" (1.58 mm) larger than the diameter of the dowel or fastener used.
TWIST: Twist is 1-1/2" (38 mm) long. Specify the length from the end of the anchor to the start of the twist. Twist is not available on steel larger than 1/4" (6.35 mm) x 1" (25.4 mm), 3/16" (4.76 mm) x 1-1/2" (38 mm) or Stainless Steel larger than 3/16" (4.76 mm) x 1" (25.4 mm) or 1/8" (3.17 mm) x 1-1/2" (38 mm).
 
 

With our extensive custom fabrication capability, Heckmann can provide the types of metal and corrosion resistant treatments to meet your specifications including the following:
STAINLESS STEEL: Stainless Steel provides the greatest level of corrosion resistance in most building environments, and is especially recommended for use with light colored stone subject to staining.
Sheet: ASTM A 167 and ASTM A 240, Type 304 ASTM A 167-96.

Plate, Bars, and Shapes: ASTM A 666, ASTM A 167, ASTM A 276 or ASTM A 479, Type 304.
Wire: ASTM A 580, ASTM A 479, Type 304, Annealed and Ground.
 
 

HOT DIP GALVANIZED AFTER FABRICATION: ASTM A 153. These heavy zinc coatings are applied after fabrication to assure that welds and exposed edges are plated. They are frequently specified for exposed conditions and critical exterior wall applications. Specify type of uncoated steel to be used.
Class B-1: 2.00 avg. oz/sq.ft. zinc
Class B-2: 1.50 avg. oz/sq.ft. zinc
Class B-3: 1.30 avg. oz/sq.ft. zinc
 

Stone Anchor Engineering Services are available in certain states through Heckmann for a fee. Call for details.

Heckmann Building Products Inc.
1501 N. 31st Avenue
Melrose Park, IL 60160-2911
Toll-Free: (800) 621-4140
Tel: (708) 865-2403
Fax: (708) 865-2640
E-mail: heckmann@worldnet.att.net
Web site: heckmannbuildingprods.com