GAF Materials Corporation
1361 Alps Road
Wayne, NJ 07470
Tel: (800) 766-3411
Web site: http://www.gaf.com

ACCESSORIES

PRODUCT DESCRIPTION
The Drill-Tec Masonry Anchor is designed to attach termination bar to concrete or masonry walls. This fastener is available with either a long-lasting stainless steel or zinc plated steel pin. There are two diameters available, 1/4" and 3/16". The lengths range from 7/8" to 2".

APPLICATION
Predrill a 1/4" or 3/16" hole using a carbide tip SDS or straight shank drill bit. The diameter of the hole must match the shank diameter of the masonry anchor. The predrilled hole must be a minimum of 1/2" deeper than the anchor embedment.The Drill-Tec Masonry Anchor is then installed with a hammer.
Minimum fastener embedment into the wall should be 5/8" for the 3/16" shank masonry anchor and 3/4" for the 1/4" shank masonry anchor.
 
PHYSICAL DATA
SKU #
 Diam. Length
Packaging
Weight

All Drill-Tec Masonry Anchors are available in 1000 piece bulk cartons or 1000 piece cartons which contain ten 100 piece boxes.

Diameter:                         3/16" or 1/4"

Material:                          Zinc Alloy

Pin Material:                    Zinc Plated Steel or Stainless Steel
 
 457F
1/4"
 1"
 1000
20 lb
 457H
1/4"
 1 1/4"
 1000
22 lb
457J
1/4"
 1 1/2"
 1000
25 lb
457L
1/4"
 2"
 1000
31 lb 
 STAINLESS STEEL PIN
 457G
1/4"
 1"
 1000
19 lb
 457I
1/4"
 1 1/4"
 1000
22 lb
 457K
1/4"
 1 1/2"
 1000
25 lb
457M
1/4"
2"
1000
32 lb

Fast Facts
The Drill-Tec Masonry Anchor is designed to attach termination bar to concrete or masonry walls.

FEATURES & BENEFITS
•Typical pullout values in cured concrete (3000 psi) are 400 lbs. for the 3/16" shank diameter, 800 lbs. for the 1/4" shank diameter zinc alloy anchors.
•Available with either long-lasting stainless steel or zinc plated steel pin.
•The GSA number for government projects is FFS-325, Group V, Type 2, Class 3 for zinc alloy anchors.

PLATES & ACCESSORIES
To be used with channel, lip or flat termination bar, depending on application. See Pressure Bar section.
Use a 1/4" or 3/16" carbide tip SDS or straight shank drill bit.

DRILL-TEC™ MASONRY ANCHOR SPECIFICATIONS
The fastener will be a Drill-Tec Masonry Anchor. The fastener must meet GSA specification number FFS-325, Group V, Type 2, Class 3. The fastener must be made in America.

APPLICATION
Predrill a 1/4" or 3/16" hole using a carbide tip SDS or straight shank drill bit. The diameter of the hole must match the diameter of the masonry anchor. The predrilled hole must be a minimum of 1/2" deeper than fastener embedment. The Drill-Tec Masonry Anchor is then installed with a hammer.
Minimum fastener embedment into the substrate should be 3/4" for a masonry anchor with a 1/4" diameter or 5/8" for a masonry anchor with 3/16" diameter.

PHYSICAL DATA
Shank Diameter: 3/16" or 1/4"         Shank Material: Zinc Coated Steel or Nylon
Pin Material: Zinc Coated Steel or Stainless Steel
Packaging:1000/Bulk Carton or 1000/Carton of ten individual 100 count boxes.

1. Insert Drill-Tec Masonry Anchor through the mounting holes in the termination bar and into the predrilled hole.
2. Tap lightly until head of anchor body is set gently against the termination bar.
 

3. Hammer pin flush to expand the body.