DoorKing, Inc. -6300 Commercial and Industrial

DOWNLOADS

The unique configuration of these Operators allows the gate arm to rotate from underneath the Operator, enabling the arm to attach to the bottom rail of the gate, were it is virtually unseen from outside the gate.


Category: commercial gate operators | gates | swing gate operators...

MasterFormat: Gate Operators



DoorKing, Inc.
120 S. Glasgow Avenue
Inglewood, CA 90301
Tel: (800) 826-7493
Fax: (310) 641-1586

info@doorking.com

https://www.doorking.com/

Find a rep/distributor

Request More Info

DOWNLOADS

Related Products

Overview


6300 Commercial and Industrial

The unique configuration of these Operators allows the gate arm to rotate from underneath the Operator, enabling the arm to attach to the bottom rail of the gate, were it is virtually unseen from outside the gate. The fully enclosed Operators prevent water from contaminating the output shaft, bearings, and electronics. Additionally, the frame is built from G90 galvanized steel to prevent rusting. These Operators can be installed directly on a concrete pad, or post-mounted to meet any installation requirements.

With safety in mind, these Operators contain an electronic and mechanical inherent reverse system for two methods of obstruction detection. The automatic electronic limits, along with the microprocessor-based electronic control board provide advanced features not typically found in Operators in this class.

The 6300 series operators are designed to operate vehicular swing gates in residential, commercial and industrial applications. These operators are designed so that they can be either pad or post mounted without any costly and time consuming field modifications. You need to specify which mounting method when ordering. The unique design of these operators allows the gate arm to be attached to the bottom rail of the gate. This eliminates the need for any brackets to be welded to the face of the gate and creates an aesthetically pleasing installation.


Features:
  • Self-adjusting, no maintenance magnetic limits.

  • Overlap feature for dual swing gate operation.

  • Designed with a built-in primary and secondary entrapment prevention system.

  • Ports for plug-in loop detectors.

  • Two convenience outlets.

  • Fail-safe release.

  • Tamper detect circuit.

  • Gate tracker reporting output.

  • Programming switches.

  • Built-in reset switch.

  • Built-in power On/Off switch.

Specifications:
Model 6300 with 1/2 HP Motor
  • Maximum gate width 18-feet.

  • Maximum gate weight 700 pounds*. (*Assumes gate swings level and is in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)

  • Swings gate 90 degrees in approximately 15-seconds.

  • 1/2 HP continuous-duty motor.

  • 115, 230*, 460* VAC. (*230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)

  • Class I, II, III and IV applications.

  • Compliant with UL 325 and 991. ETL Listed. (Note: To be compliant with UL 325 and industry safety guidelines, additional Type B1 and/or Type B2 entrapment protection devices need to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)

  • Dimensions (operator only): 16.25"W x 13.5"H* x 32 "D (* Height of operator only. Actual height above ground is determined by which mounting method is used)

Model 6300 with 1 HP Motor
  • Maximum gate width 22-feet.

  • Maximum gate weight 800 pounds*. (*Assumes gate swings level and is in good condition with properly adjusted hardware. Other external factors may affect the performance of the gate operator.)

  • Swings gate 90 degrees in approximately 15-seconds.

  • 1 HP continuous-duty motor.

  • 115, 230*, 460* VAC. (*230 and 460 volt units use a step-down power transformer to achieve 115 volt operating voltage.)

  • Class I, II, III and IV applications.

  • Compliant with UL 325 and 991. ETL listed. (Note: To be compliant with UL 325 and industry safety guidelines, additional Type B1 and/or Type B2 entrapment protection devices need to be installed with this gate operator. Your professional DKS system installer can provide you with more details on these devices and on current industry safety standards.)

  • Dimensions (operator only): 16.25"W x 13.5"H* x 32 "D (* Height of operator only. Actual height above ground is determined by which mounting method is used)

Options:

Primary / secondary connection cable (secondary operator is shipped with 50-feet of cable).
Post or pad mount - specify which.
Plug-in loop detectors.
Heater kit for cold environments.
Surge suppressors.


See More


Specifications

Entrapment Protection
System reverses gate on contact.
Suitable for single or dual gate configurations
Unique Design
Simplifies installation & provides easy access to all internal parts.
Smooth Operation
Soft Start/Soft Stop provides smooth gate operation.
Styles
Pad MountPost Mount
Sweetsstakes