C-Cure
13001 Seal Beach Boulevard
Seal Beach, CA 90740
Tel: (800) 895-2874
Fax: (562) 598-4008

Grouts
C-Cure grouts are available sanded and non-sanded in 40 colors. We also offer a patented epoxy system in 16 standard colors that span to 125 color variations.

AR Grout 922
Commercial Sanded Grout

PRODUCT DESCRIPTION
AR Grout is a blend of Portland cement, specially graded silica sand and colorfast pigments that form a dense matrix, free of any voids. In addition, special chemicals have been added to provide for a superior grout that offers ease of workability and clean-up, rapid cure, high compressive strength, low shrinkage, good bond strength and color control. AR is highly resistant to bacteria, fungus, oils and alkalies. It is non-toxic, non-dusting and does not contain iron.

AREA OF USE
AR can be used in any installation, residential to heavy commercial, where joint widths will be in excess of 1/8" up to 1/2" (3.2 up to 12.7 mm). For joint widths wider than 1/2" (12.7 mm) use PaverMix 928 grout. It is a specially designed, high performance colored grout to be used with quarry, slate, pavers, brick and cement tiles for both interior or exterior use. Only the addition of water is required to produce a dense smooth grout. As an alternate to water, CureCrylic 938 Admixture can be used to intensify its bond and flexural strength for installations subjected to thermal shock. AR should be mixed with CureCrylic 938 admixture when grouting tiles with absorption rates greater than 7%.

LIMITATIONS
AR, because of its Portland cement base, should not be used in areas where high acid resistance is required. In areas of intermittent mild acid exposure, AR out-performs conventional sand/cement grouts. The potential for efflorescence is inherent in all cement based products and is not considered a manufacturing defect.

APPLICABLE STANDARDS
AR may be used in installations that must conform to ANSI 108.1, A108.4, A108.5, A108.7, A108.10 and A118.6 H2.1.
Colors – AR is available in 40 standard colors. Upon special request, it can be custom blended to almost any color to fulfill the needs of both decorators and architects.
Texture – Powder, consisting of Portland cement, graded silica sand, colorfast pigments, organic and inorganic chemicals.

PACKAGING
50 lb. (22.7 Kg) and 25 lb. (11.3 Kg) multi-wall bags and 10 lb. (4.54 Kg) containers.

MP NonSanded 923
Latex-Portland Cement Grout

PRODUCT DESCRIPTION
MP NonSanded is a one-part, Latex-Portland cement grout that provides the user the highest performance available in the industry, in an easy to use, just-add-water material. Its unique blend of Portland cement, specially graded silica fillers, latex modifiers and colorfast pigments provides for a superior grout with excellent flexural and bond strengths, color control, minimal efflorescence and high compressive strength. MP NonSanded is specifically designed for tile installations that will be subjected to thermal shock. It resists bacteria, fungus and alkalies and does not shrink or dust.

AREA OF USE
MP NonSanded Latex-Portland Cement Grout is for small joints that do not exceed 1/8" (3.2 mm). It would most commonly be used in interior or exterior applications with porous-bodied tiles on any ceramic or mosaic job where very smooth and narrow joints are required. MP NonSanded is formulated to provide the optimum in high wear, stain resistance and exceptional color uniformity without the addition of latex admixtures. Only the addition of water is required. MP NonSanded offers improved workability with minimal labor required for final clean-up.

LIMITATIONS
MP NonSanded, because of its Portland cement base, should not be used where high acid resistance is required. In areas of intermittent mild acid exposure, MP NonSanded out performs conventional dry-set grouts. MP NonSanded is not effected by prolonged contact with water, but does not form a waterproof barrier. The potential for efflorescence is inherent in all cement based products and is not considered a manufacturing defect.

APPLICABLE STANDARDS
MP NonSanded may be used in installations that must conform to ANSI A118.6-H2.3 and H2.4.
Colors – MP NonSanded is available in 40 standard colors. Upon special request, it can be custom blended to almost any color to fulfill the needs of both decorators and architects.
Texture – Fine powder consisting of Portland cement, colorfast pigments, latex modifiers and organic and inorganic chemicals.

PACKAGING
25 lb. (11.3 Kg) multi-wall bags, 5 lb. (2.27 Kg) and 10 lb. (4.54 Kg) containers.

MP Sanded 924
Latex-Portland Cement Grout

PRODUCT DESCRIPTION
MP Sanded is a one-part, Latex-Portland cement grout that provides the user the highest performance available in the industry, in an easy to use, just-add-water material. Its unique blend of Portland cement, specially grades silica fillers, latex modifiers and colorfast pigments provides for a superior grout with excellent flexural and bond strengths, color control, minimal efflorescence and high comprehensive strength. MP Sanded is specifically designed for tile installations that will be subjected to thermal shock. It resists bacteria, fungus, alkalies and does not shrink or dust.

AREA OF USE
MP Sanded Latex-Portland Cement Grout is for medium to wide-joint installation, 1/8" - 1/2" (3.2 - 12.7 mm). It would most commonly be used in residential and commercial areas where premium grout is needed to perform under demanding job conditions. MP Sanded is formulated so that it can provide the optimum in high wear, stain resistance and exceptional color uniformity without the necessary latex admixtures of other competitive grout systems. Only the addition of water is required. Unlike any grout to date, MP Sanded offers improved workability with minimal labor required for final clean-up.

LIMITATIONS
MP Sanded, because of its Portland cement base, should not be used where high acid resistance is required. In areas of intermittent mild acid exposure, MP Sanded out-performs standard commercial Portland cement grouts. MP Sanded is not effected by prolonged contact with water, but does not form a waterproof barrier. The potential for efflorescence is inherent in all cement based products and is not considered a manufacturing defect.

APPLICABLE STANDARDS
MP Sanded may be used in installations that must conform to ANSI A118.6-H2.4, A108.1, A108.4, A108.5, A108.7 and A108.10.
Colors – MP Sanded is available in 40 standard colors. Upon special request, it can be custom blended to almost any color to fulfill the needs of both decorators and architects.
Texture – Powder consisting of Portland cement, graded silica sand, colorfast pigments, latex modifiers, organic and inorganic chemicals.

PACKAGING
25 lb (11.3Kg) multi-wall bags and 10 lb. (4.54 Kg) containers.

Supreme 925
Dry-Set Grout

PRODUCT DESCRIPTION
Supreme Dry-Set Grout is a chemically intensified Portland cement based grout which possesses exceptional working qualities and permanent joint life. It is non-shrinking, non-toxic and odorless. Supreme inhibits fungus growth and contains an inhibitor to neutralize complex heavy metal salt stains common with some soft bisque ceramic tiles.

AREA OF USE
Supreme is used in any installation area, residential or commercial, where joint widths will not be in excess of 1/8" (3.2 mm). It is most commonly used with absorptive or semi-vitreous ceramic tile for both interior and exterior use. Supreme, because of its very fine texture, is an excellent grout for use with highly glazed tiles to produce a smooth, dense joint. Only the addition of water is required. As an alternative to water, CureMix 937, CureCrylic 938 or ColorCure 945 can be used to intensify its bond and flexural strength plus improve its color intensity and stain resistance for installations subject to exterior or severe use.

LIMITATIONS
Supreme, because of its Portland cement base, should not be used where high acid resistance is required. In areas of intermittent mild acid exposure, CureMix 937, CureCrylic 938 or ColorCure 945 used in lieu of water will improve its resistance to staining, thermal shock and acid. Supreme is not effected by prolonged contact with water, but does not form a waterproof barrier. The potential for efflorescence is inherent in all cement based products and is not considered a manufacturing defect.

APPLICABLE STANDARDS
Supreme may be used in installations that must conform to ANSI 108.1, A108.4, A108.5, A108.7, A108.10 and ANSI A118.6-H-2.3.
Color – Supreme is commonly available in white or gray. Colors are available in some areas.
Texture – Fine powder, consisting of Portland cement, organic and inorganic chemicals.

PACKAGING
5 lb. (2.27 Kg) and 10 lb. (4.54 Kg) containers, 25 lb. (11.3 Kg) multi-wall bags.

CurePerfect 930
Latex-Portland Cement Grout System

PRODUCT DESCRIPTION
The CurePerfect Grout System marks the latest step in the evolution of grouting systems for ceramic tile, marble and stone surfaces. It solves the most persistent problems encountered with traditional Portland cement based grouts by providing a product with the following features:

• Enhanced color uniformity
• Expanded color range
• Resistance to bacteria
• Improved stain resistance
• Higher efflorescence resistance
• Optimum combination of bond and flexural strengths

CurePerfect is a two (2) part system (patented design and formulation) that mixes to produce a polymer modified Portland cement grout.

1. The CurePerfect Powder Base Component is available in two grades: white sanded and white non-sanded. All grades are a blend of Portland cement, chemical admixtures, organic and inorganic chemicals and specially graded silica or powdered mineral filler.
2. The CurePerfect Liquid Colorant is a pre-dispersed emulsion of latex polymers, mineral pigments, dispersants, mildewcides and cement curing compounds.

The CurePerfect Grout System is a precise chemical formulation that not only offers the aesthetic quality desired of a cement based grout, but also eliminates the problems associated with past products. CurePerfect provides the ultimate in grouting performance by ensuring the complete hydration of the Portland cement in the product, thus eliminating the problems normally associated with cement grouts. CurePerfect is available in 40 standard colors. Upon special request, large quantities can be custom blended to almost any color to fulfill the needs of both decorators and architects.

AREA OF USE
CurePerfect may be used when grouting any type of ceramic tile, stone or marble on exterior or interior residential or commercial installations.

CurePerfect grout with Sanded base may be used for medium to wide grout joints from 1/8" to 1/2" (3.2 to 12.7 mm). CurePerfect grout with NonSanded base may be used for small joints not to exceed 1/8" (3.2 mm).

CurePerfect grout is not affected by prolonged contact with water but does not form a waterproof barrier.

LIMITATIONS
Because of its Portland cement base, the CurePerfect Grout System should not be used where high acid resistance is required. Mechanical mixers used with CurePerfect must be 300 RPM or below to avoid entrapping air which will weaken grouts. Mix and apply in a temperature range between 60°F and 90°F (16°C and 32°C). Do not allow grout to freeze for the first 72 hours.

APPLICABLE STANDARDS
CurePerfect may be used in installations that must conform to ANSI A118.6-H2.3, A118.6-H2.4, A108.1, A108.4, A108.5, A108.7 and A108.10.
CurePerfect is protected under the rights and privileges of U.S. patent #4,204,876, 5,558,708, Canadian patent #1,124,912 and other pending United States and foreign patent applications.
Colors – CurePerfect is available in 40 standard colors.
Texture –
Liquid Colorant: Liquid consisting of latex polymers, special additives and pre-dispersed mineral pigments.
Base: Powder consisting of Portland cement, graded silica sand or powdered mineral filler, latex modifiers, organic and inorganic chemicals.

PACKAGING
Sanded Units
Size: 10 lb. (4.54 Kg) Sanded Unit consisting of one (1) 10 lb. (4.54 Kg) pail of Sanded Powder Base and one (1) 36 oz. (1.06L) bottle of Liquid Colorant.
Size: 35 lb. (15.9 Kg) Sanded Unit consisting of one (1) 35 lb. (15.9 Kg) bag of Sanded Powder Base and one (1) 1 gal. (3.8L) bottle of Liquid Colorant.
NonSanded Units
Size: 5 lbs. (2.27 Kg) NonSanded Unit consisting of one (1) 5 lb. (2.27 Kg) pail of NonSanded Powder Base and one (1) 36 oz. (1.06L) bottle of Liquid Colorant.
Size: 17 1/2 lb. (7.9 Kg) NonSanded Unit consisting of one (1) 17 1/2 lb. (7.9 Kg) bag of NonSanded Powder Base and one (1) gal. (3.8L) bottle of Liquid Colorant.

EverWhite 932
Chemical Resistant Water Cleanable Tile Setting & Grouting Epoxy

PRODUCT DESCRIPTION
EverWhite is a three component 100% solids blend of epoxies and silica fillers specially formulated to retain its brilliant white coloring even during prolonged exposure to direct sunlight. It is to be used for the setting and grouting of ceramic tile and pavers over a wide variety of substrates. It produces a mortar that is stain resistant, impermeable, and high in strength and shock resistant. EverWhite has exceptionally high resistance to acids, alkalies and most solvents.

BASIC USE
EverWhite can be used as both a setting and grouting mortar for virtually any tile available. It may be used for both floor or wall installations. It is used in a mortar as thin as 1/16" to 1/8" (1.6 mm to 3.2 mm) after tiles have been properly embedded. It is water cleanable before curing, non-flammable, and easy to work. EverWhite is not affected by prolonged contact with water, but does not necessarily form a waterproof barrier unless special precautions are taken to maintain a continuous film of epoxy mortar 3/32" (2.4 mm) thick with no gaps.

AREA OF USE
Suitable backings, when properly prepared, include plumb and true masonry, concrete, cured Portland cement mortar beds, brick, ceramic tile, cementitious backer units, glass, steel and fiberglass. Exterior grade plywood and gypsum board are suitable substrates in dry interior areas only.

LIMITATIONS
EverWhite should not be used in an environment above 250°F (121°C) for any extended period of time and must be mixed and used exactly as directed on labels. When used to install tile in an area that will be continually wet (e.g. swimming pools, gang showers, etc.), it is recommended that the complete installation shall be cured a minimum of 3 days prior to water exposure. A thoroughly dry, full cure of 14 days is necessary prior to full submersion with chemically treated water.

APPLICABLE STANDARDS
Conforms to requirements for chemical-resistant, water-cleanable tile setting and grouting epoxy found in ANSI A108.6 and A118.3.
Color – White.
Texture – Two separate organic liquids and a special graded silica sand packaged by weight to form a plastic mortar when combined.

PACKAGING
A 1/2 Gallon (1.89 L) Unit consists of:
One (1) Part A 0.6 lbs. (0.27 Kg) epoxy hardener, One (1) Part B 1.38 lbs. (0.63 Kg) epoxy resin, and One (1) Part C 5.25 lbs. (2.38 Kg) silica.

ColorSet Epoxy 931
Chemical Resistant Water Cleanable Tile Setting & Grouting Epoxy

PRODUCT DESCRIPTION
ColorSet Epoxy is a patented 100% solids blend of epoxies and silica fillers. It is to be used for the setting and grouting of ceramic tile and pavers over a wide variety of substrates, interior or exterior. It produces a mortar that is stain resistant, impermeable and high in strength and shock resistant. ColorSet Epoxy has exceptionally high resistance to acids, alkalies and most solvents.

BASIC USE
ColorSet Epoxy can be used as both a setting and grouting mortar for virtually any tile available, including green marble. It may be used for both floor or wall installations in a mortar as thin as 1/16" to 1/8" (1.6 mm to 3.2 mm) after tiles have been properly embedded. It is water cleanable before curing, non-flammable and easy to work. ColorSet Epoxy is not affected by prolonged contact with water, but does not necessarily form a waterproof barrier unless special precautions are taken to maintain a continuous film of epoxy mortar 3/32" (2.4 mm) thick with no gaps.

AREA OF USE
Suitable backings, when properly prepared, include plumb and true masonry, concrete, cured Portland cement mortar beds, brick, ceramic tile, cementitious backer units, steel, glass and fiberglass.

Areas of particular use are in industrial plants, particularly chemical and food processing plants such as dairies, breweries, bottling plants and textile and metal finishing plants, where the use of acids, alkalies, solvents, strong detergents and other chemicals cause erosion and damage to the setting beds and grout joints.

Other areas include hospitals, restaurants, food preparation areas and similar installations where clinical sanitation is maintained by harsh cleaning methods – countertops, backsplashes, tub and shower areas, sunken tile tubs and swimming pools – requiring a completely waterproof system.

LIMITATIONS
ColorSet Epoxy should not be used in an environment with requirements above 250°F (121°C) for any extended period of time and must be mixed and used exactly as directed on labels. When used to install tile in an area that will be continually wet (e.g. swimming pools, gang showers, etc.), it is recommended that the complete installation shall be cured a minimum of three (3) days prior to water exposure. A thoroughly dry, full cure of 14 days is necessary prior to full submersion with chemically treated water.

APPLICABLE STANDARDS
Conforms to requirements for chemical-resistant, water cleanable tile setting and grouting epoxy found in ANSI A108.6 and ANSI A118.3.
Colors – 16 standard colors providing 125 variations.
Texture – Two components (A & B) consisting of paste-like materials. Colored curing agent (hardener, Part A) and a liquid resin/ silica sand (Part B) packaged by weight to form a plastic mortar when combined. C-Cure’s ColorSet 931 is protected under the rights and privileges of U.S. patent #5362322.

PACKAGING
Contractor Unit Consists of – Part A: one (1) 2.25 lb. (1.02 Kg) container of pigmented liquid epoxy hardener; PLUS Part B: one (1) 25.2 lb. (11.43 Kg) liquid epoxy resin combined with silica filler.
1 Gal. (3.8L) Unit Consists of – Part A: two (2) 0.6 lb. (0.28 Kg) containers of pigmented liquid epoxy hardener PLUS Part B: one (1) 12.6 lb. (5.72 Kg) container of liquid epoxy resin combined with silica filler.
1/2 Gal. (1.9L) Unit Consists of – Part A: one (1) 0.6 lb. (0.28 Kg) container of pigmented liquid epoxy hardener PLUS Part B: one (1) 6.3 lb. (2.86 Kg) container of liquid epoxy resin combined with silica filler.

GUARANTEE
The recommendations, suggestions, statements and technical data are based on the best knowledge available to C-Cure and are given for informational purposes ONLY and without any responsibility for their use.

C-Cure MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT SOLD HEREIN except that the quality of the ingredients shall be in accordance with C-Cure specifications. It is expressly understood and agreed that the buyer’s sole and exclusive remedy shall be replacement of defective products and under no circumstances shall C-Cure be liable for incidental or consequential damages. C-Cure neither assumes nor authorizes any others to assume for it any liability with respect to furnishing of the product. Handling and use of the product are beyond the control of C-Cure, therefore, no warranty is made, expressed or implied, as to the results obtained from the use of the product or against any claims for infringement of patents resulting from the use of the product.

This writing constitutes a complete and exclusive statement of the understanding between C-Cure and buyer. There were no oral agreements or warranties, expressed or implied, collateral to or affecting the furnishing of the product. This understanding shall not be modified except in writing by an officer of C-Cure.

Members of National Tile Contractors Association, Materials & Methods Standards Association, Ceramic Tile Distributors Association.

NOTICE: The information in this bulletin is presented in good faith, but no warranty, expressed or implied, is given nor is freedom from any patent. In as much as any assistance furnished by C-Cure with reference to the safe use and disposal of its products is provided without charge, C-Cure assumes no obligation or liability therefore, except to the extent that any such assistance shall be given in good faith.