C-Cure
13001 Seal Beach Boulevard
Seal Beach, CA 90740
Tel: (800) 895-2874
Fax: (562) 598-4008

Underlayments
Proper preparation of the substrate – the first step to a successful and lasting tile, stone or resilient flooring installation. C-Cure's family of underlayments can prep even the most difficult substrate conditions. From scratch coat and self-leveling materials to the industry's only trowel-applied, water proofing membrane system, our high quality products prepare and protect all your flooring installation needs.

UniLayment FastSet 969
Fast Setting Polymer-Modified Portland Cement Underlayment and Patching Compound

PRODUCT DESCRIPTION
UniLayment FastSet is a fast-curing, latex modified, mildew-resistant, Portland cement based leveling and patching compound for floors prior to the installation of resilient flooring, carpet, ceramic tile, slate, granite or marble. For general applications, UniLayment FastSet requires only water to develop a dense, water resistant surface. When UniLayment FastSet is properly mixed (with water), it will featheredge to a non-checking, non-cracking, durable surface 0 - 1/2" thick (0 - 12.7 mm). UniLayment FastSet is available in two grades: Sanded and Non Sanded.

BASIC USE
UniLayment FastSet is used for rapid patching and leveling uneven, rough or unfinished concrete surfaces. It may be used over cementitious backer units on interior installations (over exterior grade plywood) and properly prepared old cutback adhesive.

AREA OF USE
UniLayment FastSet may be used on interior or exterior applications where a permanent water resistant surface is required. UniLayment FastSet hardens by hydration (curing). Like all Portland cement products, strength increases significantly during the initial 28 days. UniLayment FastSet may be applied as thick as 1/2" (12.7 mm) to featheredge in a single application without fear of shrinking, cracking or spalling.

LIMITATIONS
Do not use UniLayment FastSet over gypsum-based surfaces, old adhesive residue, paints, particle board, luan plywood, plastics, vinyl products, epoxy or urethane floor coverings. Use in temperature range of 40ºF to 90ºF (4°C to 32ºC) (Do not allow mortar to freeze for the first 72 hours.) UniLayment FastSet shall never be applied to dry concrete. Dampen concrete floor with clean water but do not let puddles remain. Apply underlayment while floor is still damp. UniLayment FastSet may be used as a wearing surface in areas which do not require high chemical resistance or will not exceed moderate traffic (equivalent to passing test cycles 1 through 10 of ASTM C-627) i.e., light institutional and commercial installations. For installation of rubber tile and other non-porous backed flooring, use an epoxy or a pressure sensitive adhesive.

APPLICABLE STANDARDS
Color—Gray
Texture—Powder, consisting of Portland cement, sand (Sanded Grade only), organic and inorganic materials.

PACKAGING
25 lb. (11.3 Kg) multi-wall bags.

Featheredge™ FastSet 979
Fast Setting Polymer-Modified Portland Cement Skim Coating, Leveling & Patching Underlayment

PRODUCT DESCRIPTION
Featheredge™ FastSet is a non sanded (Portland cement) compound for the skim coating, leveling and patching of floors prior to the installation of resilient flooring, carpet, ceramic tile, slate, granite or marble. It features the performance characteristics of a patching material that can produce a fine featheredge finish.

Polymer-modified, Featheredge FastSet is a one part system that only requires the addition of water to produce a dense, water resistant surface. The creamy consistency and wetter surface properties provide excellent workability, and when properly mixed, it will featheredge to a non-checking, non-cracking, durable surface 0 - 1/2" (0 - 12.7 mm) thick.

BASIC USE
Featheredge FastSet is used for rapid patching and leveling uneven, rough or unfinished concrete surfaces. It may be used over cementitious backer units on interior installations (over exterior grade plywood) and properly prepared old cutback adhesive.

AREA OF USE
Featheredge FastSet may be used on interior or exterior applications where a permanent water resistant surface is required. Featheredge FastSet hardens by hydration (curing). Like all Portland cement products, strength increases significantly during the initial 28 days. Featheredge FastSet may be applied as thick as 1/2" (12.7 mm) to featheredge in a single application without fear of shrinking, cracking or spalling.

LIMITATIONS
Do not use Featheredge FastSet over gypsum-based surfaces, old adhesive residue, paints, particle board, luan plywood, plastics, vinyl products, epoxy or urethane floor coverings. Use in a temperature range of 40ºF to 90ºF (4°C to 32ºC). (Do not allow mortar to freeze for the first 72 hours.) Featheredge FastSet shall never be applied to dry concrete. Featheredge FastSet may be used as a wearing surface in areas which do not require high chemical resistance or will not exceed moderate traffic (equivalent to passing test cycles 1 through 10 of ASTM C-627) i.e., light institutional and commercial installations. For installation of rubber tile and other non-porous backed flooring, use an epoxy or a pressure sensitive contact adhesive.

APPLICABLE STANDARDS
Color—Gray.
Texture—Powder, consisting of Portland cement, mineral filler, organic and inorganic materials.

PACKAGING
25 lb. (11.3 Kg) multi-wall bags.

ProFinish 989
Skim Coat, Patching & Finishing Cement Underlayment

PRODUCT DESCRIPTION
ProFinish 989 is a non sanded (Portland cement) compound for the skim coating and finishing of interior or exterior subfloors prior to the installation of resilient flooring such as vinyl and VCT, carpet, ceramic tile, slate, granite or marble. ProFinish 989 provides a smooth finish and allows the installation of floor coverings in as little 15 minutes with its revolutionary self-drying, Controlled Cure Technology.

BASIC USE
Use to smooth ridges, patch cracks and holes, or as a skim coat on concrete, interior plywood, ceramic tile, stone, cement terrazzo, sheet vinyl and properly prepared old cutback adhesive. It features the performance characteristics of a patching material that can produce a fine featheredge finish. Polymer-modified, ProFinish 989 is a one part system that only requires the addition of water to produce a dense, water resistant surface.

AREA OF USE
ProFinish 989 may be used on interior or exterior applications where a permanent, water resistant surface is required. Like all Portland cement products, strength increases significantly during the initial 28 days. ProFinish 989 may be applied as thick as 3" (7.6 cm) to featheredge in a single application without fear of shrinking, cracking or spalling.

LIMITATIONS
Do not use ProFinish 989 over gypsum based surfaces, paints, particle board, luan plywood, plastics, vinyl products, epoxy or urethane floor coverings. Use in a temperature range of 40°F to 90°F (4°C to 32°C). (Do not allow mortar to freeze for the first 72 hours.) For installation of rubber tile and other non-porous backed flooring, use an epoxy or a pressure-sensitive contact adhesive. Flooring requiring special adhesives that may be sensitive to moisture should only be installed after ProFinish 989 has cured 16 hours.

APPLICABLE STANDARDS
Color—Gray.
Texture—Texture-Powder, consisting of Portland cement, organic and inorganic materials.

PACKAGING
15 lb. (6.8 Kg) pails.

LatexUnderlayment Regular 962 HiBuild 967
Floor Leveling System

PRODUCT DESCRIPTION
LatexUnderlayment is a self-curing, liquid latex/ Portland cement-based floor leveling system for leveling most types of floors prior to installation of resilient floor coverings, carpet and ceramic tile. A development of our own research laboratory, LatexUnderlayment represents a major improvement in a cementitious leveling material.

• LatexUnderlayment Regular 962

Designed for pours from featheredge to 3/8" (9.5 mm) thickness.
• LatexUnderlayment HiBuild 967

Designed for pours from 1/8" to 1 1/2" (3.2 mm to 38 mm) thickness.

Easy to mix and to apply, LatexUnderlayment will featheredge without crumbling due to special particle distribution. When properly mixed, LatexUnderlayment will not shrink when setting, resists breakdown due to dampness, and cures to a semi-resilient but very tough surface that will not check, creak or break-up.

LatexUnderlayment will enable you to prepare all types of subfloors from small spot jobs to large areas where an extremely smooth and durable surface is required prior to installing all types of floor coverings.

AREA OF USE
LatexUnderlayment may be used for both interior and exterior applications where a permanent water-resistant surface is required. In addition to providing a surface for decorative floor coverings, it may be used as a wearing surface. HiBuild Underlayment is an excellent resurfacer for garage and warehouse floors. LatexUnderlayment will accept all types of adhesives and coatings after proper curing.

LIMITATIONS
LatexUnderlayment must not be used over gypsum-based surfaces, particle board, plastics or steel. Apply in temperature range of 40°F to 90°F (4°C to 32°C). (Do not allow mortar to freeze for the first 72 hours.)

APPLICABLE STANDARDS
There are no industry standards established for this product.
Color—Gray
Texture—Powder: consisting of Portland cement, graded sand, organic and inorganic chemicals. Liquid: White, free flowing liquid.

PACKAGING
Regular Powder – 40 lb. (18.1 Kg) multi-wall bags.
HiBuild Powder – 50 lb. (22.7 Kg) multi-wall bags.
Liquid – 4/1 gal. (3.8 L) cases, 5 gal. (18.9 L) pails, 55 gal. (208 L) drums.

LevelCure Primer 943
Vinyl Emulsion Primer

PRODUCT DESCRIPTION
LevelCure Primer is a high quality emulsion polymer for self-leveling underlayment. A bonding agent and fortifying admixture, LevelCure reduces water absorption associated with concrete to ensure a flowable mix.

BASIC USE
As a bonding agent, LevelCure Primer provides increased adhesion to old concrete and other substrates. As an additive to cementitious self-leveling underlayments, LevelCure Primer retards moisture loss, thereby reducing brittleness and increasing flexural and impact strengths. Traditional methods of covering the installation with polyethylene, burlap or fogging can be eliminated.

AREA OF USE
Use as a substrate primer on approved interior installations prior to the application of LevelCure. May also be used as an admixture to LevelCure.

LIMITATIONS
LevelCure Primer provides excellent results with intermittent water exposure, but is not recommended for use in areas of continuous exposure, such as showers or steam rooms.

APPLICABLE STANDARDS
There are no industry accepted standards for latex bonding agents.
Color—White Liquid.
Texture—Medium viscosity liquid.

PACKAGING
4/1 gallon (3.8 L) bottles.
5 gallon (18.9 L) pails.
55 gallon (208 L) drums.

LevelCure SLU 961
Self-Leveling Underlayment 0-3/8" (0-9.5 mm)

PRODUCT DESCRIPTION
LevelCure SLU Self-Leveling Underlayment is the state-of-the-art in Portland cement technology. With the sole addition of water, it becomes a free flowing liquid mortar that seeks its own level and produces a smooth flat surface. LevelCure SLU has been designed as an underlayment for the fast leveling and smoothing of floor surfaces with a minimum of labor required. The resulting finish is a smooth and durable surface that is acceptable for the installation of all floor coverings.

BASIC USE
LevelCure SLU is used anywhere an uneven, rough or unfinished concrete surface must be leveled or smoothed before application of ceramic tile, marble, wood, resilient floor coverings or carpets. In addition to leveling concrete floors, LevelCure SLU can be used in rehabilitation projects where old terrazzo, ceramic tile, wooden floors and steel decking must be made ready for new floor coverings.

AREA OF USE
LevelCure SLU may be used on interior applications where a permanent water-resistant surface is required for receiving decorative floor coverings. LevelCure SLU hardens quickly by hydration (curing). Surfaces can be walked on in two (2) to four (4) hours and can have floor coverings installed within 12 to 24 hours. When cured, the finished underlayment will have similar properties to concrete. LevelCure SLU may be applied as thick as 3/8" (9.5 mm) to featheredge in a single application without fear of shrinking, cracking or spalling. Because its application requires no troweling, LevelCure SLU provides the installer considerable cost and time savings over conventional mortars and underlayments.

LIMITATIONS
LevelCure SLU must not be used over gypsum-based surfaces, old adhesive residue, paints, particle board, plastics, vinyl, epoxy or urethane floor coverings. Use in the temperature range of 40ºF to 100ºF (4ºC to 38ºC). (Do not allow mortar to freeze for the first 72 hours.) LevelCure SLU shall never be applied to any surface unless it has been previously primed with LevelCure Primer to provide adhesion to the substrate and allow the underlayment to retain water for improved flow and higher strengths. LevelCure SLU shall not be used as a wearing surface. LevelCure SLU is for interior use only. Do not use LevelCure SLU over substrates subject to hydrostatic pressure. The LevelCure SLU shall not be applied greater than 3/8" (9.5 mm) in a single pour.

APPLICABLE STANDARDS
Color—Gray.
Texture—Powder, consisting of Portland cement, graded sand, organic and inorganic chemicals.

PACKAGING
50 lb. (22.7 Kg) multi-wall bags.

LevelCure LCB 951
Self-Leveling Underlayment 1/8"-1" (3.2 mm - 25 mm)

PRODUCT DESCRIPTION
LevelCure LCB Self-Leveling Underlayment is the state-of-the-art in Portland cement technology. With the sole addition of water, it becomes a free flowing liquid mortar that seeks its own level and produces a smooth flat surface. LevelCure LCB has been designed as an underlayment for the fast leveling and smoothing of floor surfaces with a minimum of labor required. The resulting finish is a smooth and durable surface that is acceptable for the installation of all floor coverings.

BASIC USE
LevelCure LCB is used anywhere an uneven, rough or unfinished concrete surface must be leveled or smoothed before application of ceramic tile, marble, wood, resilient floor coverings or carpets. In addition to leveling concrete floors, LevelCure LCB can be used in rehabilitation projects where old terrazzo, ceramic tile, wooden floors and steel decking must be made ready for new floor coverings.

AREA OF USE
LevelCure LCB may be used on interior applications where a permanent water-resistant surface is required for receiving decorative floor coverings. LevelCure LCB hardens quickly by hydration (curing). Surfaces can be walked on in two (2) to four (4) hours and can have floor coverings installed within 12 to 24 hours. When cured, the finished underlayment will have similar properties to concrete. LevelCure LCB may be applied as thick as 1/8" to 1" (3.2 to 25 mm) in a single application without fear of shrinking, cracking or spalling. Because its application requires no troweling, LevelCure LCB provides the installer considerable cost and time savings over conventional mortars and underlayments.

LIMITATIONS
LevelCure LCB must not be used over gypsum-based surfaces, old adhesive residue, paints, particle board, plastics, vinyl, epoxy or urethane floor coverings. Use in the temperature range of 40°F to 90°F (4°C to 32°C). (Do not allow mortar to freeze for the first 72 hours.) LevelCure LCB shall never be applied to any surface unless it has been previously primed with LevelCure Primer to provide adhesion to the substrate and allow the underlayment to retain water for improved flow and higher strengths. LevelCure LCB shall not be used as a wearing surface. LevelCure LCB is for interior use only. Do not use LevelCure LCB over substrates subject to hydrostatic pressure.

APPLICABLE STANDARDS
Color—Gray.
Texture—Powder, consisting of Portland cement, graded sand, organic and inorganic chemicals.

PACKAGING
50 lb. (22.7 Kg) multi-wall bags.

UltraCure 971
Elastomeric Waterproofing and Anti-Fracture Membrane

PRODUCT DESCRIPTION
C-Cure UltraCure is a cementitious based elastomeric anti-fracture waterproofing membrane modified with an acrylic polymer that will produce a tile setting adhesive specially developed for the installation of all types of tile, marble and stone over a variety of surfaces. UltraCure is trowel applied to develop a continuous positive moisture barrier with excellent adhesion to wood, dry concrete slabs, steel, plastic laminate countertops, concrete block and cementitious backer units.

BASIC USE
C-Cure UltraCure is used to waterproof the substrate prior to installation of vinyl tile, rubber tile, brick, marble, slate, strip wood, parquet, stone and ceramic tile. C-Cure UltraCure is also used as an anti-fracture membrane under thinset or “mud-bed” ceramic tile or stone installations to prevent cracks in the substrate from transferring to the tile. Due to its excellent flexibility, UltraCure allows the installation of hard surfaces to substrates subject to vibrations and deflection up to 1/240 of the span. With special precaution, UltraCure can be used as the adhesive to bond the tile or stone directly to the substrate.

AREA OF USE
UltraCure can be used on exterior or interior for both vertical or horizontal applications requiring integral waterproofing such as laundry areas, residential and commercial kitchens, counter tops, balconies, showers, spas and virtually anywhere elastomeric waterproofing material is specified.

UltraCure can also be used to set tiles and stone over hard to bond to surfaces such as existing vinyl flooring, ceramic tile and old cutback adhesives (in dry above grade areas), if they are well bonded to the substrate. Certain high compressive strength gypsum mortar beds are also suitable substrates when properly prepared (see C-Cure Technical Bulletin #104).

When used as a crack suppressant elastomeric membrane, UltraCure allows installations over properly prepared cracks or control joints with less than 1/8" (3.2 mm) movement.

LIMITATIONS
Do not apply to surfaces below 40ºF (4ºC) or above 90ºF (32ºC). Keep above 40ºF (4ºC) at least 72 hours after application to allow for proper cure. Do not apply over wet surfaces. Do not use as a wearing surface. Do not use over substrates subject to hydrostatic pressure. Not recommended to set hard tiles over cushion-back resilient flooring. Do not use to set high lug-back ceramic tile. Use over exterior grade plywood and gypsum board are limited to interior applications only. Because of its soft nature, marble should not be installed over substrates with movement in excess of 1/360 of the span. Do not use as a bonding mortar to install green marble. Do not apply to aluminum, stainless steel, galvanized or copper surfaces. When used as an adhesive over vitreous surfaces, allow for additional cure time.

APPLICABLE STANDARDS
UltraCure exceeds the American National Standards Institute’s Specifications for Load Bearing, Bonded, Waterproof Membranes For Thin Set Ceramic Tile And Dimension Stone Installations—ANSI A118.10. UltraCure may be used in all installations that must conform to ANSI A108.5, Installation of Ceramic Tile—ANSI 136.1, Type I, Organic Adhesives and CTI-64-2.1, Organic Tile Setting Adhesive.

PACKAGING
UltraCure is packaged as follows:
A Two Gallon (7.6 L) Unit consists of: 1.2 gallon (4.5 L) pail of UltraCure Liquid; 13 lb. (5.9 Kg) plastic bag of UltraCure Powder; 1 Quart (.94 L) of UltraCure Flashing Liquid; and 50 ft. (15.2 m) roll of UltraCure Flashing Mat. Packaged as a unit in a 5 gallon (18.9 L) plastic pail.
A Four Gallon (15.1 L) Unit consists of: 2.4 gallon (9.1 L) pail of UltraCure Liquid; 26 lb. (11.8 Kg) bag of UltraCure Powder. Packaged independently, UltraCure Flashing Liquid and UltraCure Flashing Mat are required components for waterproofing. Flashing Kits may be ordered to supplement two (2) and four (4) gallon units.
A Flashing Kit consists of: 1 quart (.94 L) of UltraCure Flashing Liquid; 1 50 ft. (15.2 m) roll of UltraCure Flashing Mat. Packaged in corrugated box.

Pro-Red Waterproofing Membrane 963
Elastomeric Waterproofing and Anti-Fracture Membrane

PRODUCT DESCRIPTION
PRO-RED WATERPROOFING MEMBRANE is a water based, ready-to-use, elastomeric waterproofing and anti-fracture membrane. PRO-RED WATERPROOFING MEMBRANE is brush or roller applied to produce a continuous moisture barrier prior to the installation of tile, stone, vinyl or rubber tile, stripwood or parquet. Use to reduce crack transmission in ceramic tile or stone floors with excellent adhesion to concrete slabs, concrete block, cementitious backer units and exterior grade plywood. Meets ANSI 118.10 for waterproofing membranes. For all interior or exterior commercial and residential tile installations.

BASIC USE
PRO-RED WATERPROOFING MEMBRANE is used as a positive waterproof membrane on substrates prior to the installation of ceramic tile, vinyl tile, rubber tile, brick, strip wood, parquet, dimensional stone, and various types of alkaline surfaces. The elastomeric properties when used under latex portland cement mortar or over "mud bed" installations, help reduce the risk of substrate cracks transferring to tile or stone. When fully dried, it performs well when continuously exposed to water.

AREA OF USE
PRO-RED WATERPROOFING MEMBRANE can be used for interior, exterior, vertical, and horizontal applications. The PRO-RED WATERPROOFING MEMBRANE elastomeric properties permit the installation of hard surfaces to substrates subject to deflection up to 1/240th of the span.

LIMITATIONS
Do not apply to surfaces that may go below 40°F (4.5°C) during the first 72 hours after application. PRO-RED WATERPROOFING MEMBRANE is not designed to be used as a leveling or patching material and must never be applied over 1/8" (3.2 mm) thick. Do not use over substrates subject to hydrostatic pressure. PRO-RED WATERPROOFING MEMBRANE is not a wear surface.

APPLICABLE STANDARDS
Meets the requirements for Load Bearing Waterproof Membranes found in ANSI A118.10.
Color - Red.
Texture - Viscous liquid.

PACKAGING
5 Gal. (18.9 L) pails.
 

SoundCure 970
Light Weight Cement Acoustical Underlayment

PRODUCT DESCRIPTION
SoundCure is a two component light weight Portland cement based acoustical underlayment developed to reduce impact and transmitted sound through hard flooring systems.

SoundCure meets city and county codes, required sound ratings for hard tile floor surfaces that exceed an Impact Insulation Class (IIC) rating of 50 and an Impact Noise Ratio (INR) of greater than 0, as determined by ASTM E-492-86 and ASTM E-989-84, as well as a Sound Transmission Class (STC) rating of not less than 50 (determined in accordance with ASTME-413-87 and ASTM E-90-87).

SoundCure eliminates the need for heavy, thick bed, labor intensive acoustical systems that require time consuming installations of costly plastic composites.

SoundCure achieves sound ratings with a simple, quicker method by setting tiles directly over an easy to apply, thin, lightweight latex modified cementitious product.

BASIC USE
When applied as thin as 1/2" (12.7 mm) over concrete floors, SoundCure provides a solid, load bearing base with high bond strengths for the installation of ceramic tile, marble, slate and hard wood flooring. SoundCure is water and weather resistant and is ideal for entries, bathrooms, kitchens, dining areas, balconies, decks in high rise apartments, offices, hotels, schools, condominiums and libraries, whenever sound control is required.

LIMITATIONS
SoundCure, because of its Portland cement base, should not be used where high acid resistance is required. The surface temperatures must be above 40°F (4°C) during applications. Keep from freezing for 72 hours. SoundCure must not be used over gypsum-based surfaces, asphalt, old adhesive residue, coatings, curing compounds, plastics, plywood, particle board, vinyl, epoxy or urethane floor covering.

Color — Gray (White upon request)

PACKAGING KIT
Two 55 lb. (25 Kg) bags of powder.
One 5 gal. (18.9 L) bucket of latex.

QuickSet with Additive 972
Latex-Modified Fast Setting Patching Compound

PRODUCT DESCRIPTION
QuickSet with Additive is a gypsum-based product designed specifically for the repair and patching of existing floors and walls. Its blend of gypsum and special vinyl polymers provide a superior patching mortar with improved bond strength to concrete, wood and gypsum plaster.

BASIC USE
QuickSet with Additive needs only the addition of water to provide a fast-setting mortar (normally 20 minutes) with excellent workability for feathering and sanding. QuickSet with Additive will not shrink or expand when properly mixed. It is ideally suited for smoothing over small holes and gouges in masonry, dry wall or seams in underlayment grade plywood subfloors.

AREA OF USE
QuickSet with Additive may be used over cementitious surfaces, wood and dry wall. QuickSet with Additive must be used in interior dry areas only. Within eight hours, under normal conditions, it is ready for application of most types of adhesives and floor or wall coverings. Always check to assure patch is dry prior to installation of flooring materials.

LIMITATIONS
QuickSet with Additive should not be used in areas exposed to moisture. Use in a temperature range of 40°F (4°C) to 100°F (38°C). QuickSet with Additive is not a wearing surface. Do not apply over 1/2" (12.7 mm) thick. Do not use under ceramic tile installations. Not recommended on concrete slabs in contact with earth or where moisture migration is possible.

APPLICABLE STANDARDS
There are no industry standards established for this product. Always check with the manufacturer of the flooring material as to the suitability of bonding to gypsum patch.
Color—White.
Texture—Powder, consisting of gypsum, fine mineral aggregate, organic and inorganic chemicals.

PACKAGING
25 lb. (11.3 Kg) multi-wall bags.

GUARANTEE
The recommendations, suggestions, statements and technical data are based on the best knowledge available to C-Cure and are given for informational purposes ONLY and without any responsibility for their use.

C-Cure MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT SOLD HEREIN except that the quality of the ingredients shall be in accordance with C-Cure specifications. It is expressly understood and agreed that the buyer's sole and exclusive remedy shall be replacement of defective products and under no circumstances shall C-Cure be liable for incidental or consequential damages. C-Cure neither assumes nor authorizes any others to assume for it any liability with respect to furnishing of the product. Handling and use of the product are beyond the control of C-Cure, therefore, no warranty is made, expressed or implied, as to the results obtained from the use of the product or against any claims for infringement of patents resulting from the use of the product.

This writing constitutes a complete and exclusive statement of the understanding between C-Cure and buyer. There were no oral agreements or warranties, expressed or implied, collateral to or affecting the furnishing of the product. This understanding shall not be modified except in writing by an officer of C-Cure.

Members of National Tile Contractors Association, Materials & Methods Standards Association, Ceramic Tile Distributors Association.

NOTICE: The information in this bulletin is presented in good faith, but no warranty, expressed or implied, is given nor is freedom from any patent. In as much as any assistance furnished by C-Cure with reference to the safe use and disposal of its products is provided without charge, C-Cure assumes no obligation or liability therefore, except to the extent that any such assistance shall be given in good faith.