Products For Rebar
No. 374 STEELWICHTM
CMU Telecoping Rebar PositionerTM. (Patent
Pending)
"The Original Telescoping
Rebar Positioner"TM:
This new unique device holds and
precisely centers rebar in a block core. The unique STEEL-WICH CMU Telescoping
Rebar PositionerTM allows for unlimited
vertical movement of the rebar during block wall installation!
The "STEEL-WICH Method"TM:(Patent
Pending) Using the CMU Adjustable Rebar Holder, the mason acquires a new
capability to "Telescope" rebar during placement. This allows reinforcing
steel to be installed with ease, in area of a masonry wall, which was difficult,
if not impossible to do before.
Advantages of the "STEEL-WICH
Method"TM:
-
Increases a Mason's Productivity
and Reduces Labor costs, with NO overrun costs whatsoever!
-
No Overhead lifting of heavy block over
Rebar, "No Rebar in your face"!
-
Ability to install reinforcing steel
with limited overhead clearance through the use of "Telescoping Rod
Action".
-
Eliminates Rebar Waste, by accurate
and secure placement method.
-
Provides superior structural strength
in masonry wall construction by precise location of vertical reinforcing
steel.
-
Full tensile strength of rebar may be
realized, thus meeting specified building codes and designs.
-
Eliminates the need to grout block wall
cores in sections and allows for a monolithic pour of grout.
-
Block integrity preserved, no waste
of grout, controls the flow of grout, and provides containment within the
vertical core.
-
Selective vertical and horizontal positioning
of rebar possible, ensuring natural and mechanical bonds with grout.
-
Allows vertical Rebar to "cross" horizontal
bond beam rebar at the top of masonry walls.
-
No problems with mechanical systems
interfering with reinforcing steel.
-
Customize Rebar reinforcement on every
job, without the extra cost.
Two sizes available: 374-S for
1/2" (13 mm) and 5/8" (16 mm) reinforcement rods and 374-L for 3/4" (19
mm), 7/8" 22 mm), and 1" (25 mm) reinforcement rods. Available Plain Steel
or Electro Plated.
No. 375 BarLoc®
Rebar Connector (U.S. Patent No. 4968176)
The BarLoc® Rebar
Connector is a coupling device which joins overlapping rebar inside concrete
block. It is a one-piece unit 7" (178mm) long made from 24 gage mill galvanized
steel. BarLoc® is designed to accommodate any length of
rebar overlap. Available in two sizes, 1/2" for 1/2" rebar and 3/4" for
5/8" and 3/4" rebar.
Key Features: Helps to assure that
both rebar joining and proper required overlap of rebar are accomplished.
BarLoc® rotates to facilitate the centering of the rebar
inside the block. The BarLoc® increases productivity by
saving time and money. It reduces worker fatigue by eliminating the need
to lift each block up and over the rebar.
No. 376 Rebar Positioner
Available in Mill galvanized and
Hotdip Galvanized for 8" (203 mm), 10" (254 mm), and 12" (305 mm) blocks.
Assists in centering rebar. Eye
is 1" (25.4 mm) in diameter.
Heckmann Building Products Inc.
1501 N. 31st Avenue
Melrose Park, IL 60160-2911
Toll-Free: (800) 621-4140
Tel: (708) 865-2403
Fax: (708) 865-2640
E-mail: info@heckmannanchors.com
Web site: http://www.heckmannbuildingprods.com
|