Metal Roofing Englert Series 2100

Englert, Inc.
1200 Amboy Avenue
P.O. Box 149
Perth Amboy, NJ 08861
Tel: (732) 826-8614
Fax: (732) 826-8865
Email: englert.inc@prodigy.net
Web site: http://www.englertinc.net

PRODUCT PRESENTATION
Englert Series 2100, 1-1/2" high seam, is a variable width panel system set to rollform at 12", 16", 20" and 24" o.c. seam spacing with stiffening ribs. The panels are secured by fixed or floating clips, allowing for unrestricted thermal movement. The panels are seamed either 90° or 180° by electric seamers. All fasteners are concealed.

Clip spacing is 24" o.c. for panels up to 16" wide. Clips are at 16" - 18" o.c. on panel widths at 20" and 24" o.c., with two fasteners per clip. Fixed clips are recommended on panel lengths under 40'. Use floating clips on panel runs over 40'.

As an integrated roofing system, Series 2100 1-1/2" high panel profiles may be installed over purlins* or solid deck (at least 1/2" thick plywood or 22 ga. metal deck) with an underlayment of 2 layers of 15# felt. Do not install panels directly over chemically treated plywood. Minimum slope 3"/12"; for other conditions, check with manufacturer.

* Series 2100, 16" wide 1-1/2" high panel system in 24 ga. meets the structural requirements of Underwriters Laboratories, Inc. for Class 90 wind uplift resistance at 4'0" o.c. spacing over purlins, with special clips. Check with manufacturer for specific applications.

SPECIFICATIONS
NOTE TO SPECIFIER: Englert Series 2100 Panel System serves the structural needs of roofing/fascia, mansard, and siding systems.

The Series 2100 Panel System may be specified for application over solid deck, 1/2" plywood or 22 gauge metal deck with 2 layers of 15# felt or 1 layer of 30# felt or over open purtins at 4'0" o.c. Minimum Pitch: 1/2"/12". Specify as required.

A. Panel System shall be the Englert Series 2100, 1-1/2" high, 16" wide panels, Structural Standing Seam System (with pencil ribs and 2 mechanically seamed styles). Mechanical seaming available in 90 degrees and 180 degrees. The panels shall have baked on finish as specified by the manufacturer, in manufacturer’s standard colors. Manufacturer shall offer at least a minimum of 23 standard colors to choose from.

B. Substrate
- 24 gauge baked on finish over Galvalume ASTM A-792-83, AZ-55, 40 KSI yield point, 52 KSI tensile strength.
- * 22 gauge baked on finish over Galvalume per ASTM A-792-83, AZ-55, 40 KSI yield point, 52 KSI tensile strength.
- * .032" or .040" Aluminum Alloy 3105-H14 approved equal.
* NOTE TO SPECIFIER: 22 gauge steel and .032" and .040" aluminum are available subject to minimum order requirements. Call Englert for details.

C. Performance
1. Panel shall meet the requirements of Underwriters Laboratories, Inc. for Class 90 wind uplift resistance.
2. ASTM E-283-84 air infiltration: Maximum of 0.003 CFM/Ft² at 10 PSF pressure differential on 180 degrees seamed profile and 0.006 CFM/Ft² at 20 PSF pressure differential.
3. ASTM E-331-84 water penetration: No evidence of uncontrolled leakage on 180 degrees seamed panel at 20 psf pressure differential.
4. Panel shall display a flame spread classification of a Class 1 when tested in accordance with ASTM E-84-87.

Englert, Inc.
1200 Amboy Avenue
P.O. Box 149
Perth Amboy, NJ 08861
Tel: (732) 826-8614
Fax: (732) 826-8865
Email: englert.inc@prodigy.net
Web site: http://www.englertinc.net

Englert, Inc.

Colorado
Phone: (303) 288-8070

Connecticut
Phone: (203) 265-6704

Florida
Phone: (813) 248-2296

Massachusetts
Phone: (508) 774-0006

New Jersey
Phone: (732) 826-8610

New York
Phone: (516) 491-7700

Pennsylvania
Phone: (412) 461-1355

Tennessee
Phone: (423) 970-0090

Virginia
Phone:
(703) 922-9666
(757) 363-0622