![]()
Product Classification: 10 21 13
Sweet’s Catalog Code: 10 21 13/GEN, BuyLine 0080
General Partitions’ Baked Enamel on Galvanized-Bonderized Steel is available
in all styles for toilet partitions, showers and dressing room compartments.
The economy and durability of baked enamel makes it the popular choice for new
construction or remodeling. Periodic washing with a mild soap and an occasional
waxing with a good automobile wax will keep the finish looking new for years.
The finish is a superior quality polyester enamel applied automatically by
a hot air assisted electrostatic system, baked at 400 degrees. The exclusive
use of galvanized bonderized steel gives additional protection and enhances
adhesion. The finish shall meet or exceed the following:
Humidity 100% @ 100 degrees F. - 1000 hrs.
Salt Spray 20% @ 100 degrees F. - 300 hrs.
Water Soak @ 110 degrees F - 1000 hrs.
Hardness - 2 H. min.
The standard panel with Ribcore sound deadening reinforcement is offered as
a standard at no extra charge. Sheet metal skins are bonded under pressure to
each cell of the core with an adhesive impervious to moisture. Lighter weight,
greater strength and permanently flat panels are provided through this type
of construction.
Corner reinforcements are used on all steel partitions at exposed corners,
mechanically fused to the edges. This feature doubles the strength of the corner
and allows field repairs if and when required. It also eliminates welding and
grinding of the corners which removes the protective zinc coating as well as
part of the metal edge.
Available Colors - Please refer to the color chart on this screen. Baked enamel
products are also available in White (SW-20A) and Black (E-36). Colors available
on Quick Shipment:
SW-237 Almond
SN-548 Tan
SB-415 Admiral Blue
SA-386 Fashion Grey
Baked enamel toilet partitions may be installed with a concealed latch operating
handle, which does not require any twisting or turning of the wrist. A gentle
nudge is required to open or close the door.
- All baked enamel metal toilet partitions
shall be (indicate one or more style numbers as required): 30, floor supported;
40, floor supported with headrail; 50, ceiling hung; 60, floor to ceiling; as
manufactured by General Partitions Mfg. Corp., Erie, Pennsylvania.
- Shall
be 1" thick with two sheets of gauge level galvanized and bonderized steel formed
and bonded together before attaching die drawn molding on all four sides of
panels. Mitered reinforcements fused to corners for added structural strength.
Fillers shall be General’s Ribcore sound-deadening insulation.
- To be same construction as panels
with galvanized and bonderized steel.
- Pilasters - Shall be 1 1/4" thick
with two sheets of galvanized and bonderized steel, bonded before attaching
die drawn molding to both sides and top, mitered reinforcements fused on both
corners for added structural strength. Same construction as panel specification
outlined above. Pilasters are to be anchored to floor with standard 3/8" threaded
rod, hex nuts and washers to provide vertical adjustment and necessary strength.
- Pilasters - Shall be 1 1/4" thick
with two sheets of galvanized and bonderized steel bonded before attaching die
drawn molding to both sides. Same construction as panel specification outlined
above. Pilasters are to be anchored to floor with heavy gauge angle. Top of
pilasters to be securely braced with extruded aluminum headrail with integral
crown loafer rail.
Headrail - To be 1 7/8" x 1 5/32" x 1/16" with integral crown loafer rail, extruded
aluminum heat-treated and anodized with necessary fittings.
- Pilasters - Shall be 1 1/4" thick
with two sheets of galvanized and bonderized steel, bonded before attaching
die drawn molding to both sides and end, mitered reinforcements fused on both
corners for added structural strength. Same construction as panel specification
outlined above. Pilasters are to be anchored to overhead member (which member
is to be supplied by others) with standard 3/8" threaded rod, hex nuts and washers
to provide vertical adjustment and necessary strength.
- Pilasters - Shall be 1 1/4" thick
with two sheets of galvanized and bonderized steel bonded before attaching die
drawn molding to both sides. Same construction as panel specification outlined
above. Pilasters are to be anchored to floor and ceiling with heavy gauge angle.
- Concealed latch (No. 2000D), coat
hooks (No. 6200D), hinge brackets (No. 1250D), and door stop and keeper (No.
2060D) heavy casting non-ferrous alloy, chrome-plated. Concealed hinge (No.
1000D), works on opposing nylon cams under spring tension. Top pivot pin, mounted
within door having bearing points above and below hinge bracket.
- Wall connection brackets for panels
and pilasters to be high strength heavy chrome plated. Pilaster trim to be 3"
high .031 stainless steel. All hardware and fittings to be secured with chrome-plated
one-way vandal-proof sex bolts or No. 14 plated-steel metal screws of proper
lengths.
- Paint Baked Enamel Scope
- All shower cabinets shall be double-wall paint baked enamel with pre-cast
terrazzo receptor as manufactured by General Partitions Mfg. Corp., Erie, Pennsylvania.
- Shall be 1" thick with two sheets
of hot-dipped galvanized and bonderized steel formed and bonded together before
attaching die drawn molding on all sides of panels. Filler to be General’s
Ribcore sound-deadening insulation.
- Black and white terrazzo. Sizes
32" x 32", 36" x 36", 40" x 40" Neo-corner or 40" x 48" and 40" x 40" handicapped.
- Brass drain with stainless steel
strainer.
- Shower walls may be prepared at
factory to receive shower head and valve supplied by others. Curtains, valves,
heads, arms and soap dishes are available as optional extras.
|