Polyurethane - 1 Component Pedestrian Traffic Coatings - Sikalastic®-736 AL Textured

Single component, aliphatic, moisture cured, low VOC, elastomeric polyurethane pre-textured top coat

Sikalastic®-736 AL Textured is a single component, aliphatic, moisture cured, low VOC, elastomeric polyurethane coating intended for use as the traffic system top coat over polyurethane waterproofing membrane for pedestrian and vehicular traffic bearing applications. Sikalastic®-736 AL Textured provides superior UV resistance,slip resistance, color stability and cleanability, as well as more decorative options. Optional Sikalastic® 700 ACL accelerator can be used to speed cure time .

• LowVOC - California Compliant
• UV stable
• Integrally textured - in pail aggregate
• Superior color and gloss retention and cleanability
• Outstanding resistance to abrasion and wear
• Resistant to water and deicing salts
• Alkaline Resistant
• Range of standard colors, with custom colors available

Usage

• Multi-story parking garages
• Parking decks and ramps
• Foot bridges and walkways
• Mechanical rooms
• Stadiums and arena
• Plaza and rooftop decks
• Balconies

Advantages

• LowVOC - California Compliant
• UV stable
• Integrally textured - in pail aggregate
• Superior color and gloss retention and cleanability
• Outstanding resistance to abrasion and wear
• Resistant to water and deicing salts
• Alkaline Resistant
• Range of standard colors, with custom colors available

Packaging

5 gal. pail

Color

Gray, Charcoal and Tan; custom colors available

Product Details

Product Information

12 months in original, unopened containers

Store dry at 40-95 °F (4-35 °C).

Condition material to 65-85 °F (18-30 °C) before using.

4000 +/- 1500 cps

Technical Information

Resistant to de-icing salts.

Application

Consumption

100 ft²/gal. at 12 wet mils (10 dry mils)

83 ft²/gal. at 14 wet mils (12 dry mils)

72 ft²/gal. at 16 wet mils (14 dry mils)

62 ft²/gal. at 18 wet mils (16 dry mils)

Coverage rates provided are intended to achieve required wet film thickness under optimal conditions. Additional material may be required depending on substrate surface roughness and porosity, material ,substrate and air temperatures, and other site-dependent factors. This will result in a lower coverage rate.

Application Steps

Thoroughly mix coating using a mechanical mixer (Jiffy) at slow speed until a homogenous mixture and uniform color is obtained (typically 3 minutes). Use care not to allow the entrapment of air into the mixture.

Field Tintable Base - Add 6 Sikaflex® 2C pigment color packs to coating. Thoroughly mix coating using a mechanical mixer (Jiffy) at slow speed until a homogenous mixture and uniform color is obtained with no streaks (typically 3 minutes). Use care not to allow the entrapment of air into the mixture. The use of 6 color packs per tint base unit provides 5 % pigment by volume, and is the standard recommended tint level.

Wear coat (optional): Apply at the recommended coverage rate 18 mils wet (62 sf/gal ) using a 1/8” notched squeegee or trowel, and backroll using nap roller 1/4” or 3/8” to uniformly backroll prior to applying topcoat. It should be backrolled in every direction to create even texture. Do not dip and roll this product from pail.

Top coat: Apply at the recommended coverage rate 18 mils wet (62 sf/gal ) using 1/8” notched squeegee or trowel, and backroll using nap roller 1/4” or 3/8” to uniformly backroll . The Top coat should be backrolled in multiple directions to create even texture . Do not dip and roll this product from pail. Allow coating to cure a minimum of 4 hours at 70 °F and 50 % RH; coating must be tack free before overcoating. Allow coating to cure for a minimum of 72 hours before opening to vehicular traffic

Accelerator: Sikalastic 700 ACL may be added to Sikalastic® 736 AL Textured in order to speed cure time particularly in cold weather conditions. Mix thoroughly prior to application. Add a maximum of 1 quart to 5 gallons (or 1:20 ratio) and only to material that will be applied within 2-3 hours.

Removal

Remove liquid coating immediately with dry cloth. Once cured, coating can only be removed by mechanical means.

See More

See Less